The Measuring Instruments (Liquid Fuel and Lubricants) Regulations 2006 (revoked)

PART I U.K. PRELIMINARY

Citation and commencement U.K.

1.—(1) These Regulations may be cited as the Measuring Instruments (Liquid Fuel and Lubricants) Regulations 2006.

(2) This regulation, regulations 2, 7, 9 and 10 and Part 1 of Schedule 2 shall come into force on 30th May 2006.

(3) The remaining regulations shall come into force on 30th October 2006.

Interpretation U.K.

2.—(1) In these Regulations—

“accuracy class” means the classification of a measuring system determined in accordance with paragraph 19 of Schedule 1;

“authorised representative” means a person who is established in a member State and is authorised by a manufacturer, in writing, to act on his behalf;

“CE marking” means the CE marking referred to in regulation 12;

“the Commission” means the European Commission;

“compliance notice” means a notice served in accordance with regulation 18(2);

“conformity assessment procedure” means any procedure referred to in regulation 6;

“the Directive” means Directive 2004/22/EC of the European Parliament and of the Council of 31st March 2004 on measuring instruments M1 ;

“disqualification mark” means a mark or sticker the design of which is published by the Secretary of State and which is affixed to a measuring system in accordance with regulation 21;

“enforcement authority” means any person who is, pursuant to regulation 17, authorised to enforce these Regulations;

“enforcement notice” means a notice served in accordance with regulation 19(2);

“enforcement officer” means—

(a)

means an inspector; or

(b)

a person appointed by the Secretary of State to act on his behalf to enforce Part II of these Regulations;

“essential requirements” means the requirements set out in Schedule 1;

“flowrate range” means the range between the minimum flowrate and the maximum flowrate;

“harmonised standard” means a technical specification adopted by the European Committee for Standardisation (CEN), the European Committee for Electrotechnical Standardisation (CENELEC) or the European Telecommunications Standards Institute (ETSI) or jointly by two or all of these organisations, at the request of the Commission pursuant to Directive 98/34/EC of the European Parliament and of the Council of 22nd June 1998 laying down a procedure for the provision of information in the field of technical standards and regulations and of rules on Information Society Services M2 , as amended by Directive 98/48/EC M3 , and prepared in accordance with the General Guidelines agreed between the Commission and one or more of CEN, CENELEC and ETSI;

“instrument” has the same meaning as measuring system;

“in writing” includes text that is—

(a)

transmitted by electronic means;

(b)

received in legible form; and

(c)

capable of being used for subsequent reference;

“liquid fuel” includes lubricants and any mixture of liquid fuel and lubricants;

“M marking” means the M marking referred to in regulation 12;

“manufacturer” means a person responsible for the conformity of a measuring system with these Regulations with a view to either placing it on the market under his own name or putting it into use for his own purposes, or both;

“maximum permissible error” means, in the case of a measuring system—

(a)

when it is used for trade, the limit of error determined in accordance with regulation 15 and Schedule 5; and

(b)

when it is placed on the market or put into use, the limit of error determined in accordance with paragraph 16 of Schedule 1;

“measuring system” means a system that comprises the meter and all devices required to ensure correct measurement or intended to facilitate the measuring operations;

“meter” means equipment designed to measure continuously, memorise and display the quantity at metering conditions of liquid fuel flowing through the measurement transducer in a closed, fully charged circuit;

“minimum measured quantity” means the smallest quantity of liquid fuel for which the measurement is metrologically acceptable for the measuring system;

“normative document” means a document containing technical specifications adopted by the Organisation Internationale de Métrologie Légale, subject to the procedure stipulated in Article 16.1, the reference of which is published by the Commission in the Official Journal of the European Union pursuant to Article 16.1(b);

“notified body” means—

(a)

the Secretary of State; or

(b)

a United Kingdom notified body; and

(c)

for the purposes of regulations 4(1)(c), 19(1)(b), 21(1)(c) and 24(6), a person designated by another member State,

who has been notified to the Commission and the other member States pursuant to Article 11.1;

“notified body criteria” means the criteria set out in Part 1 of Schedule 2;

“place on the market” means making available for the first time in a member State an instrument intended for an end user, whether for reward or free of charge;

“put into use” means the first use of an instrument intended for the end user for the purposes for which it was intended;

“relevant national standard” means a standard applicable to an instrument—

(a)

implementing a harmonised standard that has been published in the Official Journal of the European Union C series; and

(b)

the reference of which is published—

(i)

in the United Kingdom by the Secretary of State; or

(ii)

in another member State by the competent authority pursuant to the third sub-paragraph of Article 13.1;

“relevant normative document” means a normative document applicable to an instrument, the reference of which is published—

(a)

in the United Kingdom by the Secretary of State; or

(b)

in another member State by the competent authority pursuant to the third sub-paragraph of Article 13.2;

“re-qualification mark” means a mark or sticker the design of which is published by the Secretary of State and which is affixed to a measuring system in accordance with regulation 22;

“sealing device” means a seal or a plug; and

“United Kingdom notified body” means a person designated under regulation 7.

(2) Other expressions used in these Regulations have the same meanings as in the Weights and Measures Act 1985.

(3) In these Regulations, a reference to a member State includes Norway, Iceland and Liechtenstein M4 .

(4) References in these Regulations to an Article, Annex or a part of Annex are references to an Article, Annex or a part of an Annex to the Directive.

Marginal Citations

M1 OJ No. L135, 30.4.04, p.1.

M2 OJ No. L204, 21.7.98, p.37.

M3 OJ No. L217, 5.8.98, p.18.

M4 The application of the Directive was extended to the European Economic Area by Decision No. 31/2005 (OJ No. L198, 28.7.05, p.20).

Yn ddilys o 30/10/2006

Application U.K.

3.—(1) Subject to paragraphs (2), (3), (4) and (5), these Regulations apply to a measuring system which is—

(a) for use for trade in the making of a continuous and dynamic measurement of liquid fuel in a quantity equal to or less than 100 litres or 100 kilograms; and

(b) first placed on the market or put into use on or after 30th October 2006.

(2) These Regulations do not apply to a measuring system—

(a) in respect of which a certificate of approval has been granted before 30th October 2006 and is in force; and

(b) which is first passed as fit for use for trade and stamped under the Measuring Equipment (Liquid Fuel and Lubricants) Regulations 1995 M5 .

(3) These Regulations do not apply to a measuring system—

(a) in respect of a pattern of which EEC pattern approval was granted before 30^th October 2006 and is in force; and

(b) which bears a mark of EEC initial verification or of EEC partial verification.

(4) These Regulations do not apply to a measuring system which is used to measure liquefied petroleum gas or liquefied natural gas.

(5) These Regulations do not apply to a measuring system which is not compliant with the essential requirements and which is displayed or presented at a trade fair, exhibition or demonstration, if a sign displayed visibly on or near the instrument clearly indicates that the instrument—

(a) is not compliant with those requirements; and

(b) cannot be acquired or used until it is made compliant with those requirements by the manufacturer.

(6) For the purposes of paragraph (3)—

(a) a grant of EEC pattern approval or the affixing of a mark of EEC initial verification shall be in accordance with the Measuring Instruments (EEC Requirements) Regulations 1988 M6 (“the 1988 Regulations”) or, in the case of any other member State, in accordance with the measures in force which implement—

(i) Council Directive 71/319/EEC M7 ;

(ii) Council Directive 71/348/EEC M8 , as amended by the Treaty of Accession 1994 M9 ; and

(iii) Council Directive 77/313/EEC M10 , as amended by Commission Directive 82/625/EEC M11 ; and

(b) the affixing of a mark of EEC partial verification shall be in accordance with the 1988 Regulations, or in the case of any other member State, in accordance with the measures in force which implement Council Directive 71/316/EEC M12 , as amended by Council Directives 72/427/EEC M13 , 83/575/EEC M14 , 87/354/EEC M15 , 87/355/EEC M16 and 88/665/EEC M17 .

Marginal Citations

M5 S.I. 1995/1014, as amended by S.I. 1998/2218, S.I. 2001/85, S.I. 2003/214 and S.I. 2003/2110.

M6 S.I 1988/186, as amended by S.I. 1988/296 and S.I. 1988/1128.

M7 OJ L202, 6.9.71, p.32, repealed by the Directive.

M8 OJ L239, 25.10.71, p.9, repealed by the Directive.

M9 Treaty concerning the accession of Norway, Austria, Finland and Sweden, signed 24.06.94.

M10 OJ L105, 28.4.77, p.18, repealed by the Directive.

M11 OJ L252, 27.8.82, p.10, repealed by the Directive.

M12 OJ No. L202, 6.9.71, p.1, OJ/SE 1971(II), p.707.

M13 OJ No. L291, 28.12.72, p.156, OJ/SE 1972, 28-30 Dec., p.71.

M14 OJ No. L332, 28.11.83, p.43.

M15 OJ No. L192, 11.7.87, p.43.

M16 OJ No. L192, 11.7.87, p.46.

M17 OJ No. L382, 31.12.88, p.42.