- Latest available (Revised)
- Original (As adopted by EU)
Commission Directive 2012/46/EU of 6 December 2012 amending Directive 97/68/EC of the European Parliament and of the Council on the approximation of the laws of the Member States relating to measures against the emission of gaseous and particulate pollutants from internal combustion engines to be installed in non-road mobile machinery (Text with EEA relevance)
When the UK left the EU, legislation.gov.uk published EU legislation that had been published by the EU up to IP completion day (31 December 2020 11.00 p.m.). On legislation.gov.uk, these items of legislation are kept up-to-date with any amendments made by the UK since then.
Legislation.gov.uk publishes the UK version. EUR-Lex publishes the EU version. The EU Exit Web Archive holds a snapshot of EUR-Lex’s version from IP completion day (31 December 2020 11.00 p.m.).
This is the original version (as it was originally adopted).
Engine type: …
Engine identification number: …
(state percentage of oil in mixture if lubricant and fuel are mixed)
a Delete as appropriate. | |||
b Shall not be greater than 10 per cent of the power measured during the test. | |||
c Insert values at engine speed corresponding to 100 % normalised speed if NRSC test uses this speed. | |||
Power PAE (kW) absorbed at various engine speedsa b, taking into account Appendix 3 to this Annex | |||
---|---|---|---|
Equipment | Intermediate speed(if applicable) | Maximum power speed(if different from rated) | Rated speedc |
Total: |
Idle: … min–1
Intermediate: … min–1
Maximum power: … min–1
Rated(2): … min–1
a Replace with values at engine speed corresponding to 100 % normalised speed if NRSC test uses this speed. | |||
Power setting (kW) at various engine speeds | |||
---|---|---|---|
Condition | Intermediate speed(if applicable) | Maximum power speed(if different from rated) | Rated speeda |
Maximum power measured at specified test speed (PM) (kW) (a) | |||
Total power absorbed by engine driven equipment as per paragraph 1.3.2 of this Appendix taking into account Appendix 3 (kW) (b) | |||
Net engine power as specified in Section 2.4 of Annex I (kW) (c) | |||
a Replace with values at engine speed corresponding to 100 % normalised speed if NRSC test uses this speed. | |||||
Dynamometer setting (kW) at various engine speeds | |||||
---|---|---|---|---|---|
Per cent load | Intermediate speed(if applicable) | 63 %(if applicable) | 80 %(if applicable) | 91 %(if applicable) | Rated speeda |
10 (if applicable) | |||||
25 (if applicable) | |||||
50 | |||||
75 (if applicable) | |||||
100 |
Deterioration Factor (DF): calculated/fixed(4)
Specify the DF values and the emission results in the following table(4):
NRSC test | ||||||
---|---|---|---|---|---|---|
DF mult/add3 | CO | HC | NOx | HC + NOx | PM | |
Emissions | CO(g/kWh) | HC(g/kWh) | NOx(g/kWh) | HC + NOx(g/kWh) | PM(g/kWh) | CO2(g/kWh) |
Test result | ||||||
Final test result with DF |
Additional control area test points (if applicable) | ||||||
---|---|---|---|---|---|---|
Emissions at test point | Engine speed | Load(%) | CO(g/kWh) | HC(g/kWh) | NOx(g/kWh) | PM(g/kWh) |
Test result 1 | ||||||
Test result 2 | ||||||
Test result 3 |
Deterioration Factor (DF): calculated/fixeda Specify the DF values and the emission results in the following tablea: Regeneration related data may be reported for Stage IV engines. | ||||||
a Delete as appropriate. | ||||||
NRTC test | ||||||
---|---|---|---|---|---|---|
DF mult/adda | CO | HC | NOx | HC + NOx | PM | |
Emissions | CO(g/kWh) | HC(g/kWh) | NOx(g/kWh) | HC + NOx(g/kWh) | PM(g/kWh) | |
Cold start | ||||||
Emissions | CO(g/kWh) | HC(g/kWh) | NOx(g/kWh) | HC + NOx(g/kWh) | PM(g/kWh) | CO2(g/kWh) |
Hot start w/o regeneration | ||||||
Hot start with regenerationa | ||||||
kr,u (mult/add)a kr,d (mult/add)a | ||||||
Weighted test result | ||||||
Final test result with DF |
Cycle work for hot start w/o regeneration kWh
Gaseous emissions(7): …
PM(7): …
Method(8): single/multiple filter
For the case of several parent engines, the following is to be indicated for each of them.
Insert engine speed corresponding to 100 % normalised speed if NRSC test uses this speed.
Uncorrected power measured in accordance with Section 2.4 of Annex I.
Delete as appropriate.
Indicate figure number of system used as defined in Annex VI Section 1 or Section 9 of Annex 4B of ECE R96 03 series of amendments, as applicable.
Delete as appropriate.
Indicate figure number of system used as defined in Annex VI Section 1 or Section 9 of Annex 4B of ECE R96 03 series of amendments, as applicable.
Delete as appropriate.’
The Whole Directive you have selected contains over 200 provisions and might take some time to download. You may also experience some issues with your browser, such as an alert box that a script is taking a long time to run.
Would you like to continue?
The Schedules you have selected contains over 200 provisions and might take some time to download. You may also experience some issues with your browser, such as an alert box that a script is taking a long time to run.
Would you like to continue?
Latest Available (revised):The latest available updated version of the legislation incorporating changes made by subsequent legislation and applied by our editorial team. Changes we have not yet applied to the text, can be found in the ‘Changes to Legislation’ area.
Original (As adopted by EU): The original version of the legislation as it stood when it was first adopted in the EU. No changes have been applied to the text.
Access essential accompanying documents and information for this legislation item from this tab. Dependent on the legislation item being viewed this may include:
Use this menu to access essential accompanying documents and information for this legislation item. Dependent on the legislation item being viewed this may include:
Click 'View More' or select 'More Resources' tab for additional information including: