Commission Regulation (EU) 2019/318Show full title

ANNEX IX

Annex X to Regulation (EU) 2017/2400 is amended as follows:

(1)

point 3.4.1 is replaced by the following:

‘3.4.1. The tyre shall be clearly identifiable in respect to the certificate covering it for the corresponding rolling resistance coefficient.’;

(2)

in point 3.4.2, the first sentence is replaced by the following:

‘The tyre manufacturer shall use the markings affixed to the side wall of the tyre or affix an additional identifier to the tyre.’;

(3)

Appendix 1 is replaced by the following:

‘Appendix 1

MODEL OF A CERTIFICATE OF A COMPONENT, SEPARATE TECHNICAL UNIT OR SYSTEM Maximum format: A4 (210 × 297 mm)

CERTIFICATE ON CO₂ EMISSIONS AND FUEL CONSUMPTION RELATED PROPERTIES OF A TYRE FAMILY

a “delete as appropriate”
Communication concerning: grantinga extensiona refusala withdrawala	Administration stamp

of a certificate on CO₂ emission and fuel consumption related properties of a tyre family in accordance with Commission Regulation (EU) 2017/2400, as amended by Commission Regulation (EU) 2019/318

Certification number: …

Hash: …

Reason for extension: …

1. Manufacturer's name and address: …

2. If applicable, name and address of manufacturer's representative: …

3. Brand name/trade mark: …

4. Tyre type description: …

(a)

Manufacturer's name …

(b)

Brand name or trade mark

(c)

Tyre class (in accordance with Regulation (EC) No 661/2009) …

(d)

Tyre-size designation …

(e)

Tyre structure (diagonal (bias-ply); radial) …

(f)

Category of use (normal tyre, snow tyre, special use tyre) …

(g)

Speed category (categories) …

(h)

Load-capacity index (indices) …

(i)

Trade description/commercial name …

(j)

Declared tyre rolling resistance coefficient …

5. Tyre identification code(s) and technology(ies) used to provide identification code(s), if applicable:

Technology:	Code:
…	…

6. Technical Service and, where appropriate, test laboratory approved for purposes of approval or of verification of conformity tests: …

7. Declared values:

7.1.

declared rolling resistance level of the tyre (in N/kN rounded to the first decimal place, in accordance with ISO 80000-1 Appendix B, section B.3, rule B (example 1))

Cr, … [N/kN]

7.2.

tyre test load in accordance with Regulation (EC) No 1222/2009 Annex I part A (85 % of single load, or 85 % of maximum load capacity for single application specified in applicable tyre standards manuals if not marked on tyre.)

F_ZTYRE … [N]

7.3.

Alignment equation: …

8. Any remarks: …

9. Place: …

10. Date: …

11. Signature: …

12. Annexed to this communication are: …’’;

(4)

Appendix 2 is amended as follows:

(a)

SECTION I is amended as follows:

points 0.14 and 0.16 are deleted;

(b)

SECTION II is amended as follows:

(i)

point 4 is replaced by the following:

‘4. Date of test report:’;

(ii)

point 8.4 is replaced by the following:

‘8.4. Alignment equation:’;

(iii)

the following point is inserted:

‘8.5. Rolling resistance level of the tyre (in N/kN rounded to the first decimal place, in accordance with ISO80000-1 Appendix B, section B.3, rule B (example 1)) C_r,aligned … [N/kN]’;

(5)

Appendix 3 is amended as follows:

(a)

the title is replaced by the following:

‘Input parameters for the simulation tool’;

(b)

in Definitions, point (1) is replaced by the following:

‘(1) “Parameter ID”

:

Unique identifier as used in the simulation tool for a specific input parameter or set of input data’;

(c)

in Table 1, the third row ‘TechnicalReportId’ below the title and the last row are replaced by the following:

‘CertificationNumber	P232	token
Dimension	P108	string	[-]	Allowed values (non-exhaustive): “9.00 R20”, “9 R22.5”, “9.5 R17.5”, “10 R17.5”, “10 R22.5”, “10.00 R20”, “11 R22.5”, “11.00 R20”, “11.00 R22.5”, “12 R22.5”, “12.00 R20”, “12.00 R24”, “12.5 R20”, “13 R22.5”, “14.00 R20”, “14.5 R20”, “16.00 R20”, “205/75 R17.5”, “215/75 R17.5”, “225/70 R17.5”, “225/75 R17.5”, “235/75 R17.5”, “245/70 R17.5”, “245/70 R19.5”, “255/70 R22.5”, “265/70 R17.5”, “265/70 R19.5”, “275/70 R22.5”, “275/80 R22.5”, “285/60 R22.5”, “285/70 R19.5”, “295/55 R22.5”, “295/60 R22.5”, “295/80 R22.5”, “305/60 R22.5”, “305/70 R19.5”, “305/70 R22.5”, “305/75 R24.5”, “315/45 R22.5”, “315/60 R22.5”, “315/70 R22.5”, “315/80 R22.5”, “325/95 R24”, “335/80 R20”, “355/50 R22.5”, “365/70 R22.5”, “365/80 R20”, “365/85 R20”, “375/45 R22.5”, “375/50 R22.5”, “375/90 R22.5”, “385/55 R22.5”, “385/65 R22.5”, “395/85 R20”, “425/65 R22.5”, “495/45 R22.5”, “525/65 R20.5”’

(6)

in Appendix 4, point 2.1 is replaced by the following:

‘1.1. Certification number for tyres shall comprise the following:

eX*YYYY/YYYY*ZZZZ/ZZZZ*T*0000*00

Section 1	Section 2	Section 3	Additional letter to section 3	Section 4	Section 5
Indication of country issuing the certificate	HDV CO2 certification Regulation (2017/2400)	Latest amending Regulation (ZZZZ/ZZZZ)	T = Tyre	Base certification number 0000	Extension 00’