- Latest available (Revised)
- Original (As adopted by EU)
Commission Regulation (EU) No 66/2014 of 14 January 2014 implementing Directive 2009/125/EC of the European Parliament and of the Council with regard to ecodesign requirements for domestic ovens, hobs and range hoods (Text with EEA relevance)
When the UK left the EU, legislation.gov.uk published EU legislation that had been published by the EU up to IP completion day (31 December 2020 11.00 p.m.). On legislation.gov.uk, these items of legislation are kept up-to-date with any amendments made by the UK since then.
Legislation.gov.uk publishes the UK version. EUR-Lex publishes the EU version. The EU Exit Web Archive holds a snapshot of EUR-Lex’s version from IP completion day (31 December 2020 11.00 p.m.).
This is the original version as it was originally adopted in the EU.
This legislation may since have been updated - see the latest available (revised) version
For the purposes of assessing conformity of products with the requirements laid down in this Regulation referred to in Article 3(2) of Directive 2009/125/EC, the authorities of the Member States shall apply the following procedure:
The Member State authorities shall test one single unit per model.
The model shall be considered to comply with the applicable requirements:
if the values provided in the product information as required by this Regulation are not more favourable for the manufacturer than the values in the technical documentation, including test reports; and
if testing of the relevant model parameters applying the tolerances listed in Table 7 shows compliance for all of those parameters.
If the result referred to in point 2(a) is not achieved, the model and all equivalent models shall be considered not to comply with this Regulation.
If the result referred to in point 2(b) is not achieved, the Member State authorities shall select three additional units of the same model for testing. As an alternative, the three additional units selected may be of one or more different models which have been listed as equivalent product in the supplier’s technical documentation.
The model shall be considered to comply with the applicable requirements if testing of the relevant model parameters listed in Table 7 shows compliance for all of those parameters.
If the result referred to in point 5 is not achieved, the model and all equivalent models shall be considered not to comply with this Regulation. The Member State authorities shall provide the test results and other relevant information to the authorities of the other Member States and to the Commission within 1 month of the decision being taken on the non-compliance of the model.
Member State authorities shall use the measurement and calculation methods set out in Annex II.
The tolerances set in this Annex shall be applied only to the verification of the measured parameters by Member State authorities, representing the allowed variations of the measurement results of the verification tests, and shall not be used by the manufacturer in establishing the values in the technical documentation or in interpreting these values with a view to achieving a better labelling classification or to communicate better performance by any means.
Verification tolerances
Measured parameters | Verification tolerances |
---|---|
Mass of the domestic oven (M) | The determined value shall not exceed the declared value of M by more than 5 %. |
Volume of the cavity of the domestic oven (V) | The determined value shall not be lower than the declared value of V by more than 5 %. |
ECelectric cavity, ECgas cavity | The determined value shall not exceed the declared value of ECelectric cavity, ECgas cavity by more than 5 %. |
ECelectric hob | The determined value shall not exceed the declared value of ECelectric hob by more than 5 %. |
EEgas hob | The determined value shall not be lower than the declared value of EEgas hob by more than 5 %. |
WBEP, WL | The determined value shall not exceed the declared value of WBEP, WL by more than 5 %. |
QBEP, PBEP | The determined value shall not be lower than the declared value of QBEP, PBEP by more than 5 %. |
Qmax | The determined value shall not exceed the declared value of Qmax by more than 8 %. |
Emiddle | The determined value shall not be lower than the declared value of Emiddle by more than 5 %. |
Sound power level LWA | The determined value shall not exceed the declared value. |
Po, Ps | The determined value of power consumption Po and Ps shall not exceed the declared value by more than 10 %. The determined value of power consumption Po and Ps of less than or equal to 1,00 W shall not exceed the declared value by more than 0,10 W. |
Latest Available (revised):The latest available updated version of the legislation incorporating changes made by subsequent legislation and applied by our editorial team. Changes we have not yet applied to the text, can be found in the ‘Changes to Legislation’ area.
Original (As adopted by EU): The original version of the legislation as it stood when it was first adopted in the EU. No changes have been applied to the text.
Access essential accompanying documents and information for this legislation item from this tab. Dependent on the legislation item being viewed this may include:
Use this menu to access essential accompanying documents and information for this legislation item. Dependent on the legislation item being viewed this may include:
Click 'View More' or select 'More Resources' tab for additional information including: