Directive 2014/45/EU of the European Parliament and of the CouncilShow full title

ANNEX III MINIMUM REQUIREMENTS CONCERNING ROADWORTHINESS FACILITIES AND TEST EQUIPMENT

I. Facilities and equipment

Roadworthiness tests undertaken in accordance with the recommended methods specified in Annex I shall be carried out by using appropriate facilities and equipment. This may include, where applicable, the use of mobile test units. The test equipment that is necessary will depend on the vehicle categories to be tested, as described in Table I. Facilities and equipment shall comply with the following minimum requirements:

(1)

A test facility with adequate space for the evaluation of vehicles which meets the necessary health and safety requirements;

(2)

A test lane of sufficient size for each test, a pit or lift and, for vehicles having a maximum mass exceeding 3,5 tonnes, a device to lift a vehicle on one of the axles, equipped with appropriate lighting and, where necessary, with aeration devices;

(3)

For testing any vehicle, a roller brake tester capable of measuring, displaying and recording the braking forces and the air pressure in air brake systems in accordance with Annex A to standard ISO 21069-1 on the technical requirements of roller brake tester or equivalent standards;

(4)

For testing vehicles having a maximum mass not exceeding 3,5 tonnes, a roller brake tester in accordance with item 3, which may not include the recording of braking forces, pedal force and the air pressure in air brake systems and their display;

or

A plate brake tester equivalent to the roller brake tester in accordance with item 3, which may not include the recording capability of the braking forces, pedal force and the display of air pressure in air brake systems;

(5)

A deceleration recording instrument, while non-continuous measurement instruments must record/store measurements at least 10 times per second;

(6)

Facilities for the testing of air brake systems, such as manometers, connectors and hoses;

(7)

A wheel/axle load measuring device to determine the axle loads (optional facilities for measuring two-wheel loads, such as wheel weight pads and axle weight pads);

(8)

A device for testing the wheel-axle suspension (wheel play detector) without lifting the axis, meeting the following requirements:

(a)

The device must be equipped with at least two power-operated plates that can be moved in opposite sense in both the longitudinal and the transversal directions;

(b)

The movement of the plates must be controllable by the operator from the testing position;

(c)

For vehicles having a maximum mass exceeding 3,5 tonnes, the plates shall comply with the following technical requirements:

• Longitudinal and transversal movement of at least 95 mm,

• Longitudinal and transversal movement speed 5 cm/s to 15 cm/s;

(9)

A Class II sound level meter, if sound level is measured;

(10)

A 4-gas analyser in accordance with Directive 2004/22/EC of the European Parliament and of the Council(1);

(11)

A device for measuring the absorption coefficient with sufficient accuracy;

(12)

One headlamp aiming device allowing the setting of the headlight to be tested in accordance with the provisions for the setting of headlights of motor vehicles (Directive 76/756/EEC); the light/dark boundary must be easily recognisable in daylight (without direct sunlight);

(13)

A device for measuring the tread depth of tyres;

(14)

A device to connect to the electronic vehicle interface, such as an OBD scan tool;

(15)

A device to detect LPG/CNG/LNG leakage, if such vehicles are tested.

Any of the above devices may be combined in one composite device, provided that this does not affect the accuracy of each device.

II. Calibration of equipment used for measurements

Unless specified otherwise by the relevant Union legislation, the interval between two successive calibrations may not exceed:

(i)

24 months for the measurement of weight, pressure and sound level,

(ii)

24 months for the measurement of forces,

(iii)

12 months for the measurement of gaseous emissions.

Table I ^a

a The vehicle categories which are outside the scope of this Directive are included for guidance.
1 P…petrol (positive ignition); D…diesel (compression ignition)
Minimum equipment required for the purpose of performing a roadworthiness test
Vehicles		Category		Equipment required for each item listed in section I
	Maximum mass			1	2	3	4	5	6	7	8	9	10	11	12	13	14	15
1. Motorcycles			1
		L1e	P	x								x	x		x	x	x
		L3e,L4e	P	x								x	x		x	x	x
		L3e,L4e	D	x								x		x	x	x	x
		L2e	P	x	x							x	x		x	x	x
		L2e	D	x	x							x		x	x	x	x
		L5e	P	x	x							x	x		x	x	x
		L5e	D	x	x							x		x	x	x	x
		L6e	P	x	x							x	x		x	x	x
		L6e	D	x	x							x		x	x	x	x
		L7e	P	x	x							x	x		x	x	x
		L7e	D	x	x							x		x	x	x	x
2. Vehicles for the carriage of persons
	Up to 3 500 kg	M1,M2	P	x	x		x					x	x		x	x	x	x
	Up to 3 500 kg	M1,M2	D	x	x		x					x		x	x	x	x
	> 3 500 kg	M2,M3	P	x	x	x		x	x	x	x	x	x		x	x	x	x
	> 3 500 kg	M2,M3	D	x	x	x		x	x	x	x	x		x	x	x	x
3. Vehicles for the carriage of goods
	Up to 3 500 kg	N1	P	x	x		x					x	x		x	x	x	x
	Up to 3 500 kg	N1	D	x	x		x					x		x	x	x	x
	> 3 500 kg	N2,N3	P	x	x	x		x	x	x	x	x	x		x	x	x	x
	> 3 500 kg	N2,N3	D	x	x	x		x	x	x	x	x		x	x	x	x
4. Special vehicles derived from a category N vehicle, T5
	Up to 3 500 kg	N1	P	x	x		x					x	x		x	x	x	x
	Up to 3 500 kg	N1	D	x	x		x					x		x	x	x	x
	> 3 500 kg	N2,N3,T5	P	x	x	x		x	x	x	x	x	x		x	x	x	x
	> 3 500 kg	N2,N3,T5	D	x	x	x		x	x	x	x	x		x	x	x	x
5. Trailers	Up to 750 kg	O1		x												x
	> 750 to 3 500 kg	O2		x	x		x									x
	> 3 500 kg	O3,O4		x	x	x			x	x	x					x

(1)

Directive 2004/22/EC of the European Parliament and of the Council of 31 March 2004 on measuring instruments (OJ L 135, 30.4.2004, p. 1).