Directive 94/9/EC of the European Parliament and the Council (repealed)Dangos y teitl llawn

Article 8 U.K.

1. The procedures for assessing the conformity of equipment, including where necessary the devices referred to in Article 1 (2), shall be as follows:

(a) equipment-group I and II, equipment-category M 1 and 1

The manufacturer or his authorized representative established in the Community must, in order to affix the CE marking, follow the CE type-examination procedure (referred to in Annex III), in conjunction with:

• (a) the procedure relating to production quality assurance (referred to in Annex IV),

  (a) or

• the procedure relating to product verification (referred to in Annex V);

(b) Equipment-group I and II, equipment-category M 2 and 2

(i)

In the case of internal combustion engines and electrical equipment in these groups and categories, the manufacturer or his authorized representative established in the Community shall, in order to affix the CE mark, follow the EC-type examination procedure (referred to in Annex III), in conjunction with:

• the procedure relating to conformity to type referred to in Annex VI, or

• the procedure relating to product quality assurance referred to in Annex VII;

(ii)

in the case of other equipment in these groups and categories, the manufacturer or his authorized representative established in the Community must, in order to affix the CE mark, follow the procedure relating to internal control of production (referred to in Annex VIII)

and

communicate the dossier provided for in Annex VIII, paragraph 3, to a notified body, which shall acknowledge receipt of it as soon as possible and shall retain it.

(c) equipment-group II, equipment-category 3

The manufacturer or his authorized representative established in the Community must, in order to affix the CE marking, follow the procedure relating to internal control of production referred to n Annex VIII;

(d) equipment-groups I and II

In addition to the procedures referred to in paragraph 1(a), (b) and (c), the manufacturer or his authorized representative established in the Community may also, in order to affix the CE marking, follow the procedure relating to CE unit verification (referred to in Annex IX).

2. The provisions of 1(a) or 1(d) above shall be used for conformity assessment of autonomous protective systems.

3. The procedures referred to in paragraph 1 shall be applied in respect of components as referred to in Article 4 (2), with the exception of the affixing of the CE marking. [X1 A written attestation shall be issued by the manufacturer] or his authorized representative established in the Community, declaring the conformity of the components with the provisions of this Directive which apply to them and stating their characteristics and how they must be incorporated into equipment or protective systems to assist compliance with the essential requirements applicable to finished equipment or protective systems.

4. In addition, the manufacturer or his authorized representative established in the Community may, in order to affix the CE marking, follow the procedure relating to internal control of production (referred to in Annex VIII) with regard to the safety aspects referred to in point 1.2.7 of Annex II.

5. Notwithstanding the previous paragraphs, the competent authorities may, on a duly justified request, authorize the placing on the market and putting into service on the territory of the Member State concerned of the equipment, protective systems and individual devices referred to in Article 1 (2) in respect of which the procedures referred to in the previous paragraphs have not been applied and the use of which is in the interests of protection.

6. Documents and correspondence relating to the procedures referred to in the abovementioned paragraphs shall be drawn up in one of the official languages of the Member States in which those procedures are being applied or in a language accepted by the notified body.

7. (a) [X1 Where the equipment, protective systems and devices referred to in Article 1(2) are] subject to other Community Directives covering other aspects which also provide for the affixing of the CE marking referred to in Article 10, that marking shall indicate [X1 that the equipment, protective systems and devices referred to in Article 1(2) are] also presumed to conform with the provisions of those other Directives.

(b) However, where one or more of those Directives allow the manufacturer, during a transitional period, to choose which arrangements to apply, the CE marking shall indicate conformity only with the Directives applied by the manufacturer. In this case, particulars of the said Directives, as published in the Official Journal of the European Communities, must be given in the documents, notices or instructions required by the Directives and [X1 accompanying the equipment, protective systems and devices referred to in Article 1(2).]

Editorial Information

X1 Substituted by Corrigendum to Directive 94/9/EC of the European Parliament and of the Council of 23 March 1994 on the approximation of the laws of the Member States concerning equipment and protective systems intended for use in potentially explosive atmospheres (Official Journal of the European Communities L 100 of 19 April 1994).