xmlns:atom="http://www.w3.org/2005/Atom"
Article 1.This Directive applies to the braking of all types of...
Article 2.The procedure for the granting of component type-approval in respect...
Article 3.In accordance with Article 11 of Directive 92/61/EEC, equivalence between...
Article 4.This Directive may be amended in accordance with Article 13...
Article 5.(1) Member States shall adopt and publish the provisions necessary...
2. CONSTRUCTION AND FITTING REQUIREMENTS
2.2. Characteristics of braking devices
2.2.1. Every two-wheel moped or two-wheel motorcycle shall be equipped with...
2.2.1.1. The two service braking devices may have a common braking...
2.2.2. Every motorcycle with sidecar shall be equipped with the braking...
2.2.3.1. either two independent service braking devices which together actuate the...
2.2.3.2. a service braking device which operates on all the wheels,...
2.2.3.3. In addition, every three-wheel moped must be equipped with a...
2.2.4.1. a foot-controlled serviced braking device which operates on all wheels,...
2.2.4.2. a parking braking device acting on the wheels of at...
2.2.5. The braking devices must act on brake surfacespermanently connected to...
2.2.6. The component parts of all braking devices, where attached to...
2.2.7. The braking devices shall operate freely when correctly lubricated and...
2.2.7.1. Wear of the brakes must be capable of being easily...
2.2.7.2. The control and the components of the transmission and of...
2.2.7.3. When correctly adjusted the components of the braking device must...
2.2.8. In braking devices where the transmission is hydraulic, the receptables...
Braking tests and performance of braking devices
1.1.1. The performance prescribed for braking devices is based on the...
1.1.2. The stopping distance is the distance covered by the vehicle...
1.1.3. For component type-approval, the braking performance must be measured during...
1.1.3.1. the vehicle's condition as regards its mass must be as...
1.1.3.3. the prescribed performance must be obtained without locking of the...
1.1.3.4. during the tests the force applied to the brake control...
1.1.4.1. The service braking tests must be carried out under the...
1.1.4.1.2. the vehicle must be loaded, when required to be tested...
1.1.4.1.3. for all the type-0 tests the brakes must be cold:...
1.1.4.1.4. the driver must shall be seated on the saddle as...
1.1.4.1.6. the test must be performed when there is no wind...
1.3. Special provisions relating to testing with wet brakes
1.3.1. Enclosed brakes: it is not necessary to carry out this...
1.3.2. The test with brakes subject to wetting must be carried...
1.3.3. The test equipment must continuously wet the brakes for each...
1.3.4. For exposed or partly exposed disc brakes, the prescribed amount...
1.3.4.1. For fully exposed disc brakes, the water must be directed...
1.3.4.2. For partly exposed disc brakes, the water must be directed...
1.3.4.3. The water must be directed on to the surface(s) of...
1.3.5. For fully enclosed disc brakes, where the provisions of 1.3.1...
1.3.7. For drum brakes, where the requirements of 1.3.1 do not...
1.3.8. Subject to the requirements of 1.3.7 and to the requirement...
1.3.9. To ensure the correct wetting of the brake(s), the vehicle...
1.4.2.1. The vehicle and the brake(s) to be tested must be...
1.4.2.2.1. for testing the front brake(s), whichever is the lower of...
1.4.2.2.2. for testing the rear brake(s), whichever is the lower of...
1.4.2.2.3. for testing a combined braking system, whichever is the lower...
1.4.2.3. The distance between the initiation of one stop and the...
1.4.2.4. The use of the gearbox and/or clutch is as follows:...
1.4.2.4.1. In the case of a vehicle with a manual gearbox...
1.4.2.4.2. In the case of a vehicle with a fully automatic...
1.4.2.5. After each stop, the vehicle must immediately be subjected to...
1.4.2.6. The force applied to the control shall be so adjusted...
2. PERFORMANCE OF BRAKING DEVICES
2.1. Provisions relating to tests of vehicles with braking devices operating...
2.2. Provisions relating to tests of vehicles of which (at least)...
2.3. Braking performance with the parking braking device (if applicable)
2.4. Provisions relating to forces applied to brake controls
2.5. Performance levels (minimum and maximum) to be attained with wet...
5.1. The following additional checks must be carried out with the...
5.1.1. Any wheel controlled by an anti-lock device must not lock...
5.1.2. Where a wheel controlled by an anti-lock device passes from...
5.1.3. Where a vehicle passes from a low-adhesion surface to a...
5.1.4. Where both independent braking devices are equipped with an anti-lock...
5.1.5. However, in the tests provided for in 5.1.1, 5.1.2, 5.1.3...