CHAPTER II F1UAS intended to be operated in the ‘ open ’ category ..., accessories kits bearing a class identification label and remote identification add-ons
SECTION 3Conformity of the product
F1Article 12Presumption of conformity
A product which is in conformity with F2the designated standards, shall be presumed to be in conformity with the requirements covered by those standards or parts thereof set out in Parts 1 to 6, 16 and 17 of the Annex.
Article 13Conformity assessment procedures
F11.
The manufacturer shall perform a conformity assessment of the product using one of the following procedures with a view to establishing its compliance with the requirements set out in Parts 1 to 6, 16 and 17 of the Annex. The conformity assessment shall take into account all intended and foreseeable operating conditions.
2.
The procedures available to conduct the conformity assessment shall be the following:
F1(a)
internal production control as set out in Part 7 of the Annex, when
F3i)
ii)
the conditions in paragraph 3 are satisfied;
(b)
F6type examination followed by conformity to type based on internal production control as set out in Part 8 of the Annex;
(c)
conformity based on full quality assurance as set out in Part 9 of the F7Annex.
F83.
The conditions in this paragraph are—
(a)
that the conformity assessment is conducted before 1st January 2028,
(b)
that the assessment is of the compliance of a product with the requirements set out in Parts 2, 3 or 4 of the Annex, and
(c)
that the product is covered by a type examination under Part 8 of the Annex to Commission Delegated Regulation (EU) 2019/945 of 12 March 2019 on unmanned aircraft systems and on third-country operators of unmanned aircraft systems as it has effect in EU Law.
Article 14F9... Declaration of conformity
F11.
The F10... declaration of conformity referred to in paragraph 8 of Article 6 shall state that compliance of the product with the requirements set out in Parts 1 to 6, 16 and 17 of the Annex has been demonstrated and, for UAS, identify its class.
2.
3.
The simplified F13... declaration of conformity referred to in paragraph 8 of Article 6 shall contain the elements set out in Part 12 of the Annex and shall be continuously updated. F14... The full text of the F13... declaration of conformity shall be available at the internet address referred to in the simplified F13... declaration of conformity F15....
F164.
Where a product is subject to more than one enactment requiring a declaration of conformity, a single declaration of conformity shall be drawn up in respect of all such enactments. That declaration shall contain the enactments concerned.
5.
By drawing up the F17... declaration of conformity, the manufacturer shall assume responsibility for the compliance of the product with the requirements laid down in this Chapter.
F18Article 15Requirements of the UK Marking
The UK marking is subject to the requirements set out in Article 30 of, and Annex 2 to, Regulation (EC) 765/2008.
Article 16Rules and conditions for affixing the F19UK marking, the identification number of the F20approved body, the UAS class identification label and the indication of the sound power level
1.
The F21UK marking shall be affixed visibly, legibly and indelibly to the product or to the data plate attached to it. Where that is not possible or not warranted on account of the size of the product, it shall be affixed to the packaging.
F12.
The UA class identification label shall be affixed visibly, legibly and indelibly to the UA or, when relevant, to each accessories of a class F22UK5 accessories kit, and its packaging and shall be at least 5 mm high. The affixing to a product of markings, signs or inscriptions which are likely to mislead third parties regarding the meaning or form of the class identification label shall be prohibited.
3.
The indication of the sound power level provided for in Part 14 of the Annex shall be affixed, when applicable, visibly, legibly and indelibly on the UA, unless that is not possible or not warranted on account of the size of the product, and on the packaging.
4.
The F23UK marking and, when applicable, the indication of the sound power level and the UA class identification label shall be affixed before the product is placed on the market.
5.
The F24UK marking shall be followed by the identification number of the F25approved body where the conformity assessment procedure set out in Part 9 of the Annex is applied.
The identification number of the F25approved body shall be affixed by the F25approved body Itself or, under its instructions, by the manufacturer or his authorised representative.
F266.
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Article 17Technical documentation
F11.
The technical documentation shall contain all relevant data and details of the means used by the manufacturer to ensure that the product complies with the requirements set out in Parts 1 to 6, 16 and 17 of the Annex. It shall, at least, contain the elements set out in Part 10 of the Annex.
2.
The technical documentation shall be drawn up before the product is placed on the market and shall be continuously updated.
3.
F14.
Where the technical documentation does not comply with paragraphs 1, 2 or 3 of this Article, the market surveillance authority may ask the manufacturer or the importer to have a test performed by a body acceptable to the market surveillance authority at the expense of the manufacturer or the importer within a specified period in order to verify compliance of the product with the requirements set out in Parts 1 to 6, 16 and 17 of the Annex which applies to it.