CHAPTER V

APPROVAL OF CONFORMITY ASSESSMENT BODIES

Approved bodies
Article 20
1.
An approved body is a conformity assessment body which—
1. has been approved by the Secretary of State pursuant to the procedure set out in Article 21 (approval of conformity assessment bodies); or
2. immediately before IP completion day was a notified body in respect of which the Secretary of State had taken no action under Article 30 of Regulation 2016/425 (pre-exit), to suspend or withdraw the body's status as a notified body.
2.
Paragraph 1 has effect subject to Article 30 (restriction, suspension or withdrawal of approval).
3.
In this Chapter—
- “
notified body
” means a body which—
  1. the Secretary of State had, before IP completion day, notified to the European Commission and the member States of the European Union in accordance with Article 20 of Regulation 2016/425 (pre-exit); and
  2. in respect of which no objections had been raised, as referred to in Article 28(5) of Regulation 2016/425 (pre-exit);
- “
approved body requirements
” means the requirements set out in Article 24.

Approval of conformity assessment bodies
Article 21
1
The Secretary of State may approve only those conformity assessment bodies that qualify for approval.
2
A conformity assessment body qualifies for approval if the first and second conditions below are met.
3
The first condition is that the conformity assessment body has applied to the Secretary of State to become an approved body and that application is accompanied by—
a
a description of—
i
the conformity assessment activities that the conformity assessment body intends to carry out;
ii
the conformity assessment procedure in respect of which the conformity assessment body claims to be competent;
iii
the category of PPE in respect of which the conformity assessment body claims to be competent; and
b
either—
i
an accreditation certificate; or
ii
the documentary evidence necessary for the Secretary of State to verify, recognise and regularly monitor the conformity assessment body's compliance with the approved body requirements.
4
The second condition is that the Secretary of State is satisfied that the conformity assessment body meets the approved body requirements.
5.
For the purposes of paragraph 4, the Secretary of State may accept an accreditation certificate provided in accordance with paragraph 3(b), as sufficient evidence that the conformity assessment body meets the approved body requirements.
6.
When deciding whether to approve a conformity assessment body that qualifies for approval, the Secretary of State may—
a
have regard to any other matter which appears to the Secretary of State to be relevant; and
b
set conditions that the conformity assessment body must meet.
7.
For the purposes of this Article, “
accreditation certificate
” means a certificate issued by the UK national accreditation body, attesting that a conformity assessment body meets the approved body requirements.

UK national accreditation body
Article 22
The Secretary of State may authorise the UK national accreditation body to carry out the following activities on behalf of the Secretary of State—
a
assessing whether a conformity assessment body meets the approved body requirements;
b
monitoring approved bodies in accordance with Article 23; and
c
compiling and maintaining the register of approved bodies, in accordance with Article 29.

Monitoring obligations
Article 23
The Secretary of State must monitor each approved body with a view to verifying that the body—
The Commission shall make that information publicly available.
a
continues to meet—
i
the approved body requirements; and
ii
any conditions set by the Secretary of State under Article 21(6)(b); and
b
carries out its functions in accordance with this Regulation.

Approved body requirements
Article 24
1
For the purposes of approval, a conformity assessment body shall meet the requirements laid down in paragraphs 2 to 11.
2
A conformity assessment body must have legal personality and must be established in—
a
the United Kingdom; or
b
the territory of a party to the CPTPP.
2A
In paragraph (2) “
the CPTPP
” has the meaning set out in section 1 of the Trade (Comprehensive and Progressive Agreement for Trans-Pacific Partnership) Act 2024.
3
A conformity assessment body shall be a third-party body independent of the organisation or the PPE it assesses.
A body belonging to a business association or professional federation representing undertakings involved in the design, manufacturing, provision, assembly, use or maintenance of PPE which it assesses, may, on the condition that its independence and the absence of any conflict of interest are demonstrated, be considered such a body.
4
A conformity assessment body, its top-level management and the personnel responsible for carrying out the conformity assessment tasks shall not be the designer, manufacturer, supplier, purchaser, owner, user or maintainer of the PPE which they assess, nor the representative of any of those parties. This does not preclude the use of assessed PPE that are necessary for the operations of the conformity assessment body or the use of such PPE for personal purposes.
A conformity assessment body, its top-level management and the personnel responsible for carrying out the conformity assessment tasks shall not be directly involved in the design, manufacture, marketing, use or maintenance of PPE, or represent the parties engaged in those activities. They shall not engage in any activity that may conflict with their independence of judgement or integrity in relation to conformity assessment activities for which they are approved. This shall in particular apply to consultancy services.
Conformity assessment bodies shall ensure that the activities of their subsidiaries or subcontractors do not affect the confidentiality, objectivity or impartiality of their conformity assessment activities.
5
Conformity assessment bodies and their personnel shall carry out the conformity assessment activities with the highest degree of professional integrity and the requisite technical competence in the specific field and shall be free from all pressures and inducements, particularly financial, which might influence their judgement or the results of their conformity assessment activities, especially as regards persons or groups of persons with an interest in the results of those activities.
6
A conformity assessment body shall be capable of carrying out all the conformity assessment tasks assigned to it by Annexes V, VII and VIII and in relation to which it has been approved, whether those tasks are carried out by the conformity assessment body itself or on its behalf and under its responsibility.
At all times and for each conformity assessment procedure and each kind of PPE for which it has been approved, a conformity assessment body shall have at its disposal the necessary:
a
personnel with technical knowledge and sufficient and appropriate experience to perform the conformity assessment tasks;
b
descriptions of procedures in accordance with which conformity assessment is carried out, ensuring the transparency and the ability of reproduction of those procedures. It shall have appropriate policies and procedures in place that distinguish between tasks it carries out as an approved body and other activities;
c
procedures for the performance of activities which take due account of the size of an undertaking, the sector in which it operates, its structure, the degree of complexity of the PPE technology in question and the mass or serial nature of the production process.
A conformity assessment body shall have the means necessary to perform the technical and administrative tasks connected with the conformity assessment activities in an appropriate manner and shall have access to all necessary equipment or facilities.
7
The personnel responsible for carrying out conformity assessment tasks shall have the following:
a
sound technical and vocational training covering all the conformity assessment activities in relation to which the conformity assessment body has been approved;
b
satisfactory knowledge of the requirements of the assessments they carry out and adequate authority to carry out those assessments;
c
appropriate knowledge and understanding of the essential health and safety requirements set out in Annex II, of the applicable designated standards, and of the relevant provisions of this Regulation and any other relevant United Kingdom legislation;
d
the ability to draw up certificates, records and reports demonstrating that assessments have been carried out.
8
The impartiality of the conformity assessment bodies, their top level management and of the personnel responsible for carrying out the conformity assessment tasks shall be guaranteed.
The remuneration of the top level management and personnel responsible for carrying out the conformity assessment tasks of a conformity assessment body shall not depend on the number of assessments carried out or on the results of those assessments.
9
Conformity assessment bodies shall take out liability insurance unless the Secretary of State is directly responsible for the conformity assessment.
10
The personnel of a conformity assessment body shall observe professional secrecy with regard to all information obtained in carrying out their tasks under Annexes V, VII and VIII or any provision of United Kingdom law giving effect to it, except in relation to the enforcement authority. Proprietary rights shall be protected.
11
Conformity assessment bodies shall participate in, or ensure that their personnel responsible for carrying out the conformity assessment tasks are informed of, the relevant standardisation activities and the activities of any approved body coordination group established by the Secretary of State and shall apply as general guidance the administrative decisions and documents produced as a result of the work of that group.

Presumption of conformity of approved bodies
Article 25
1.
Where a conformity assessment body demonstrates its conformity with the criteria laid down in a designated standard (or part of such a standard), the Secretary of State must presume that the conformity assessment body meets the approved body requirements covered by that standard (or the part of that standard).
2.
The presumption in paragraph 1 is rebuttable.

Subsidiaries of, and subcontracting by approved bodies
Article 26
1
An approved body may subcontract specific conformity assessment activities, or use a subsidiary to carry out such activities provided—
a
the body is satisfied that the subcontractor or subsidiary meets the approved body requirements;
b
the body has informed the Secretary of State that it is satisfied that the subcontractor or subsidiary meets those requirements; and
c
the economic operator for whom the activities are to be carried out has consented to the activities being carried out by that person.
2
The approved body which subcontracts specific conformity assessment activities or uses a subsidiary to carry out such activities remains responsible for the proper performance of those activities (irrespective of where the subcontractor or subsidiary is established).
3
Where an approved body subcontracts, or uses a subsidiary to carry out, a specific conformity assessment activity, the approved body must, for a period of 10 years beginning on the day on which the activity is first carried out, keep available for inspection by the Secretary of State all relevant documentation concerning—
a
the assessment of the qualifications of the subcontractor or the subsidiary; and
b
the conformity assessment activity carried out by the subcontractor or subsidiary.
4
In this Article, “
subsidiary
” has the meaning given to it by section 1159 of the Companies Act 2006.

Application for notification
Article 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Notification procedure
Article 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Identification numbers and register of approved bodies
Article 29
1
The Secretary of State must—
a
assign an approved body identification number to each approved body; and
b
compile and maintain a register of—
i
approved bodies;
ii
their approved body identification numbers;
iii
the activities for which they have been approved; and
iv
any restrictions on those activities.
2
The register referred to in paragraph 1 must be made publicly available.

Restriction, suspension or withdrawal of approval
Article 30
1
Where the Secretary of State determines that an approved body—
a
no longer meets an approved body requirement, or
b
is failing to fulfil its obligations under these Regulations, other than a condition referred to in Article 21(6)(b),
the Secretary of State must restrict, suspend or withdraw the body's status as an approved body under Article 21.
2
Where the Secretary of State determines that an approved body no longer meets a condition referred to in Article 21(6)(b), the Secretary of State may restrict, suspend or withdraw the body's status as an approved body under Article 21.
3.
In deciding what action to take under paragraph 1 or 2, the Secretary of State must have regard to the seriousness of the non-compliance.
4.
Before taking action under paragraph 1 or 2, the Secretary of State must—
a
give notice in writing to the approved body of the proposed action and the reasons for it;
b
give the approved body an opportunity to make representations to the Secretary of State regarding the proposed action within a reasonable period from the date of the notice; and
c
consider any such representations made by the approved body.
5.
Where the Secretary of State has taken action in respect of an approved body under paragraph 1 or 2, or where an approved body has ceased its activity, the approved body must, at the request of the Secretary of State—
a
transfer its files relating to the activities it has undertaken as an approved body to another approved body or to the Secretary of State; or
b
keep its files relating to the activities it has undertaken as an approved body available for inspection by the Secretary of State and market surveillance authority for a period of 10 years from the date they were created.
6.
The activities undertaken as an approved body referred to in paragraph 5 include any activities that the body has undertaken as a notified body.

Challenge of the competence of notified bodies
Article 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Operational obligations of approved bodies
Article 32
1
Approved bodies shall carry out conformity assessments in accordance with the conformity assessment procedures provided for in Annexes V, VII and VIII.
1A.
Subject to the terms of its appointment an approved body must carry out the conformity assessment activities and procedures, in respect of which—
a
the body's approval was given under Article 21; or
b
the body's notification as a notified body was made.
2
Conformity assessments shall be carried out in a proportionate manner, avoiding unnecessary burdens for economic operators. Conformity assessment bodies shall perform their activities taking due account of the size of an undertaking, the sector in which it operates, its structure, the degree of complexity of the PPE technology in question and the mass or serial nature of the production process.
In so doing they shall nevertheless respect the degree of rigour and the level of protection required for the compliance of the PPE with the requirements of this Regulation.
3
Where an approved body finds that the essential health and safety requirements set out in Annex II or the corresponding designated standards or other technical specifications have not been met by a manufacturer, it shall require the manufacturer to take appropriate corrective measures and shall not issue a certificate or approval decision.
4
Where, in the course of the monitoring of conformity following the issue of a certificate or approval decision, an approved body finds that a PPE no longer complies, it shall require the manufacturer to take appropriate corrective measures and shall suspend or withdraw the certificate or the approval decision if necessary.
5
Where corrective measures are not taken or do not have the required effect, the approved body shall restrict, suspend or withdraw any certificates or approval decisions, as appropriate.

Appeal against decisions of approved bodies
Article 33
Approved bodies shall ensure that a transparent and accessible appeal procedure against their decisions is available.

Information obligation on approved bodies
Article 34
1
Approved bodies shall inform the Secretary of State of the following:
a
any refusal, restriction, suspension or withdrawal of a certificate or approval decision;
b
any circumstances affecting the scope of or conditions for their approval;
c
any request for information which they have received from the market surveillance authority regarding conformity assessment activities;
d
on request, conformity assessment activities performed within the scope of their approval and any other activity performed, including cross-border activities and subcontracting.
2
Approved bodies shall provide other approved bodies under this Regulation carrying out similar conformity assessment activities covering the same kinds of PPE with relevant information on issues relating to negative and, on request, positive conformity assessment results.

Exchange of experience
Article 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Coordination of notified bodies
Article 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Word in Ch. 5 heading substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(18); 2020 c. 1, Sch. 5 para. 1(1)
Art. 20 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(19) (as amended by S.I. 2020/852, regs. 2(2), 4(2), Sch. 1 para. 1(u)(v)); 2020 c. 1, Sch. 5 para. 1(1)
Art. 21 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(20); 2020 c. 1, Sch. 5 para. 1(1)
Art. 22 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(21); 2020 c. 1, Sch. 5 para. 1(1)
Art. 23 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(22); 2020 c. 1, Sch. 5 para. 1(1)
Art. 24 heading substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(23)(a); 2020 c. 1, Sch. 5 para. 1(1)
Word in Art. 24(1) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(23)(b); 2020 c. 1, Sch. 5 para. 1(1)
Word in Art. 24(4) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(23)(d); 2020 c. 1, Sch. 5 para. 1(1)
Word in Art. 24(7)(a) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(23)(d); 2020 c. 1, Sch. 5 para. 1(1)
Word in Art. 24(6) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(23)(e)(i); 2020 c. 1, Sch. 5 para. 1(1)
Words in Art. 24(6)(b) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(23)(e)(ii); 2020 c. 1, Sch. 5 para. 1(1)
Word in Art. 24(7)(c) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(23)(f)(i); 2020 c. 1, Sch. 5 para. 1(1)
Words in Art. 24(7)(c) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(23)(f)(ii); 2020 c. 1, Sch. 5 para. 1(1)
Words in Art. 24(9) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(23)(g); 2020 c. 1, Sch. 5 para. 1(1)
Words in Art. 24(10) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(23)(h)(i); 2020 c. 1, Sch. 5 para. 1(1)
Words in Art. 24(10) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(23)(h)(ii); 2020 c. 1, Sch. 5 para. 1(1)
Words in Art. 24(11) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(23)(i)(i); 2020 c. 1, Sch. 5 para. 1(1)
Words in Art. 24(11) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(23)(i)(ii); 2020 c. 1, Sch. 5 para. 1(1)
Art. 25 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(24); 2020 c. 1, Sch. 5 para. 1(1)
Art. 26 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(25); 2020 c. 1, Sch. 5 para. 1(1)
Art. 27 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(26); 2020 c. 1, Sch. 5 para. 1(1)
Art. 28 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(26); 2020 c. 1, Sch. 5 para. 1(1)
Art. 29 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(27); 2020 c. 1, Sch. 5 para. 1(1)
Art. 30 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(28); 2020 c. 1, Sch. 5 para. 1(1)
Art. 31 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(29); 2020 c. 1, Sch. 5 para. 1(1)
Word in Art. 32 heading substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(30)(a); 2020 c. 1, Sch. 5 para. 1(1)
Art. 32(1A) inserted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(30)(c); 2020 c. 1, Sch. 5 para. 1(1)
Word in Art. 32(5) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(30)(a); 2020 c. 1, Sch. 5 para. 1(1)
Word in Art. 32(1) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(30)(b); 2020 c. 1, Sch. 5 para. 1(1)
Words in Art. 32(3) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(30)(d); 2020 c. 1, Sch. 5 para. 1(1)
Word in Art. 32(3) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(30)(e); 2020 c. 1, Sch. 5 para. 1(1)
Words in Art. 32(4) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(30)(d); 2020 c. 1, Sch. 5 para. 1(1)
Word in Art. 33 substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(31)(a); 2020 c. 1, Sch. 5 para. 1(1)
Word in Art. 33 heading substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(31)(b); 2020 c. 1, Sch. 5 para. 1(1)
Word in Art. 34 heading substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(32)(a); 2020 c. 1, Sch. 5 para. 1(1)
Word in Art. 34(1) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(32)(b)(i)(aa); 2020 c. 1, Sch. 5 para. 1(1)
Words in Art. 34(1) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(32)(b)(i)(bb); 2020 c. 1, Sch. 5 para. 1(1)
Words in Art. 34(1)(b) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(32)(b)(ii); 2020 c. 1, Sch. 5 para. 1(1)
Words in Art. 34(1)(c) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(32)(b)(iii); 2020 c. 1, Sch. 5 para. 1(1)
Word in Art. 34(1)(d) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(32)(b)(iv); 2020 c. 1, Sch. 5 para. 1(1)
Word in Art. 34(2) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(32)(c)(i); 2020 c. 1, Sch. 5 para. 1(1)
Words in Art. 34(2) substituted (31.12.2020) by The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(32)(c)(ii); 2020 c. 1, Sch. 5 para. 1(1)
Art. 35 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(33); 2020 c. 1, Sch. 5 para. 1(1)
Art. 36 omitted (31.12.2020) by virtue of The Product Safety and Metrology etc. (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/696), reg. 1, Sch. 35 para. 3(33); 2020 c. 1, Sch. 5 para. 1(1)
Art. 24(2) substituted (coming into force in accordance with reg. 1(2) of the amending S.I.) by The Treatment of Conformity Assessment Bodies (Comprehensive and Progressive Agreement for Trans-Pacific Partnership) Regulations 2024 (S.I. 2024/504), reg. 17(a)
Art. 24(2A) inserted (coming into force in accordance with reg. 1(2) of the amending S.I.) by The Treatment of Conformity Assessment Bodies (Comprehensive and Progressive Agreement for Trans-Pacific Partnership) Regulations 2024 (S.I. 2024/504), reg. 17(b)