http://www.legislation.gov.uk/id/eur/2014/44

CHAPTER IIOBLIGATIONS OF MANUFACTURERS REGARDING VEHICLE CONSTRUCTION

Article 3Fitting and demonstration requirements related to vehicle construction

1.

In order to comply with the vehicle construction requirements as laid down in Article 18 of, and Annex II to, Regulation (EU) No 168/2013, manufacturers shall equip L-category vehicles with systems, components and separate technical units affecting functional safety and environmental protection that are designed, constructed and assembled so as to enable the vehicle in normal use and maintained according to the prescriptions of the manufacturer to comply with the detailed technical requirements and testing procedures.

2.

In accordance with Articles 6 to 20 manufacturers shall demonstrate by means of physical demonstration testing to the approval authority that the L-category vehicles made available on the market, registered or entering into service in the Union comply with the vehicle construction requirements of Chapter III of Regulation (EU) No 168/2013 and comply with the detailed technical requirements and test procedures laid down in Articles 6 to 20 of this Regulation.

3.

Manufacturers shall ensure that spare parts and equipment that are made available on the market or are entering into service in the Union comply with the relevant requirements of Regulation (EU) No 168/2013, as specified by the detailed technical requirements and test procedures referred to in this Regulation. An approved L-category vehicle equipped with such a spare part or equipment shall meet the same test requirements and performance limit values as a vehicle equipped with an original part or equipment satisfying endurance requirements up to and including those set out in Article 22(2) and Articles 23 and 24 of Regulation (EU) No 168/2013.

4.

Manufacturers shall also ensure that type-approval procedures for verifying conformity of production are followed with regard to the detailed vehicle construction requirements laid down in Article 33 of Regulation (EU) No 168/2013 and the detailed technical requirements in this Regulation.

5.

Where applicable, the manufacturers shall submit to the approval authority a description of the measures taken to prevent tampering with the powertrain management system including the emission and functional safety control computers.

Article 4Application of UNECE regulations

1.

The UNECE regulations and amendments thereto set out in Annex I to this Regulation shall apply to type approval.

2.

Vehicles with a maximum design vehicle speed lower than or equal to 25 km/h shall meet all the relevant requirements of UNECE regulations applying to vehicles with a maximum vehicle design speed higher than 25 km/h.

3.

References to vehicle categories L₁, L₂, L₃, L₄, L₅, L₆ and L₇ in the UNECE regulations shall be understood as references to vehicle categories L1e, L2e, L3e, L4e, L5e, L6e and L7e respectively under this Regulation, including any subcategories.

Article 5Technical specifications on vehicle construction requirements and test procedures

1.

The vehicle construction test procedures shall be performed in accordance with the test requirements laid down in this Regulation.

2.

The test procedures shall be carried out or witnessed by the approval authority or, if authorised by the approval authority, by the technical service.

3.

The measurement methods and test results shall be reported to the approval authority in the test report format laid down pursuant to Article 32(1) of Regulation (EU) No 168/2013.

Article 6Requirements applying to powertrain tampering prevention (anti-tampering) measures

The test procedures and requirements applying to powertrain tampering prevention (anti-tampering) measures referred to in Annex II(C1) to Regulation (EU) No 168/2013 shall be conducted and verified in accordance with Annex II to this Regulation.

Article 7Requirements applying to the arrangements for type-approval procedures

The test procedures and requirements applying to arrangements for type-approval referred to in Annex II(C2) to Regulation (EU) No 168/2013 shall be conducted and verified in accordance with Annex III to this Regulation.

Article 8Requirements applying to conformity of production (CoP)

The test procedures and requirements applying to conformity of production (CoP) referred to in Annex II(C3) to Regulation (EU) No 168/2013 shall be conducted and verified in accordance with Annex IV to this Regulation.

Article 9Requirements applying to coupling devices and attachments

The test procedures and requirements applying to coupling devices and attachments referred to in Annex II(C4) to Regulation (EU) No 168/2013 shall be conducted and verified in accordance with Annex V to this Regulation.

Article 10Requirements applying to devices to prevent unauthorised use

The test procedures and requirements applying to devices to prevent unauthorised use referred to in Annex II(C5) to Regulation (EU) No 168/2013 shall be conducted and verified in accordance with Annex VI to this Regulation.

Article 11Requirements applying to electromagnetic compatibility (EMC)

The test procedures and requirements applying to electromagnetic compatibility (EMC) referred to in Annex II(C6) to Regulation (EU) No 168/2013 shall be conducted and verified in accordance with Annex VII to this Regulation.

Article 12Requirements applying to external projections

The test procedures and requirements applying to external projections referred to in Annex II(C7) to Regulation (EU) No 168/2013 shall be conducted and verified in accordance with Annex VIII to this Regulation.

Article 13Requirements applying to fuel storage

The test procedures and requirements applying to fuel storage referred to in Annex II(C8) to Regulation (EU) No 168/2013 shall be conducted and verified in accordance with Annex IX to this Regulation.

Article 14Requirements applying to load platforms

The test procedures and requirements applying to load platforms referred to in Annex II(C9) to Regulation (EU) No 168/2013 shall be conducted and verified in accordance with Annex X to this Regulation.

Article 15Requirements applying to masses and dimensions

The test procedures and requirements applying to masses and dimensions referred to in Annex II(C10) to Regulation (EU) No 168/2013 shall be conducted and verified in accordance with Annex XI to this Regulation.

Article 16Requirements applying to the functional on-board diagnostics

The test procedures and requirements applying to functional on-board diagnostics referred to in Annex II(C11) to Regulation (EU) No 168/2013 shall be conducted and verified in accordance with Annex XII to this Regulation.

Article 17Requirements applying to passenger handholds and footrests

The test procedures and requirements applying to passenger handholds and footrests referred to in Annex II(C12) to Regulation (EU) No 168/2013 shall be conducted and verified in accordance with Annex XIII to this Regulation.

Article 18Requirements applying to the registration plate space

The test procedures and requirements applying to the registration plate space referred to in Annex II(C13) to Regulation (EU) No 168/2013 shall be conducted and verified in accordance with Annex XIV to this Regulation.

Article 19Requirements applying to access to repair and maintenance information

The test procedures and requirements applying to access to repair and maintenance information referred to in Annex II(C14) to Regulation (EU) No 168/2013 shall be conducted and verified in accordance with Annex XV to this Regulation.

Article 20Requirements applying to stands

The test procedures and requirements applying to stands referred to in Annex II(C15) to Regulation (EU) No 168/2013 shall be conducted and verified in accordance with Annex XVI to this Regulation.