Commission Delegated Regulation (EU) No 1322/2014Show full title

CHAPTER II VEHICLE CONSTRUCTION AND GENERAL TYPE-APPROVAL REQUIREMENTS

Article 3 Manufacturer’s general obligations regarding vehicle construction

1. Manufacturers shall equip agricultural and forestry vehicles with systems, components and separate technical units affecting occupational safety that are designed, constructed and assembled so as to enable the vehicle in normal use and maintained according to the prescriptions of the manufacturer to comply with the detailed technical requirements and testing procedures set out in Articles 4 to 32.

2. Manufacturers shall demonstrate by means of physical demonstration testing to the approval authority that the agricultural and forestry vehicles made available on the market, registered or entering into service in the Union comply with the detailed technical requirements and test procedures laid down in Articles 4 to 32.

3. Manufacturers shall ensure that spare parts and equipment that are made available on the market or are entering into service in the Union comply with the detailed technical requirements and test procedures referred to in this Regulation. An approved agricultural and forestry vehicle equipped with such a spare part or equipment shall meet the same test requirements and performance limit values as a vehicle equipped with an original part.

4. Manufacturers shall ensure that type-approval procedures for verifying conformity of production are followed as regards the detailed vehicle construction requirements laid down in this Regulation.

Article 4 Application of UNECE regulations

The UNECE regulations and amendments thereto set out in Annex I to this Regulation shall apply to type-approval of agricultural and forestry vehicles subject to the conditions laid down in this Regulation.

Article 5 Recognition of test reports issued on the basis of OECD Codes for the purposes of EU type-approval

In accordance with Article 50 of Regulation (EU) No 167/2013, the test reports issued on the basis of OECD Codes set out in Annex II to this Regulation shall be recognised for the purpose of EU type approval as an alternative to the test report issued on the basis of this Regulation.

Article 6 Arrangements with regard to type-approval procedures, including the requirements relating to virtual testing

The arrangements with regard to type-approval procedures referred to in Article 20 (8) of Regulation (EU) No 167/2013 and the requirements relating to virtual testing referred to in Article 27(6) of that Regulation shall be laid down in Annex III to this Regulation.

Article 7 Arrangements with regard to conformity of production

The arrangements with regard to conformity of production referred to in Article 28(6) of Regulation (EU) No 167/2013 shall be laid down in Annex IV to this Regulation.

Article 8 Requirements with regard to access to repair and maintenance information

The requirements with regard to access to repair and maintenance information referred to in Article 53(12) of Regulation (EU) No 167/2013 shall be laid down in Annex V to this Regulation.

Article 9 Requirements applying to roll-over protection structures (dynamic testing)

The test procedures and requirements applying to roll-over protection structures as regards dynamic testing for vehicles of categories T1, T4.2 and T4.3 referred to in Article 18(2)(a) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex VI to this Regulation.

Article 10 Requirements applying to roll-over protection structures (track-laying tractors)

The test procedures and requirements applying to roll-over protection structures as regards track-laying tractors for vehicles of categories C1, C2, C4.2 and C4.3 referred to in Article 18(2)(a) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex VII to this Regulation.

Article 11 Requirements applying to roll- over protection structures (static testing)

As an alternative to the requirements laid down in Article 9 and Article 10, manufacturers may choose to comply with the requirements of this Article, where the type of vehicle falls within the field of application set out in Annex VIII to this Regulation. The test procedures and requirements applying to roll-over protection structures as regards static testing for vehicles of categories T1/C1, T4.2/C4.2 and T4.3/C4.3 referred to in Article 18(2)(a) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex VIII to this Regulation.

Article 12 Requirements applying to roll-over protection structures (front mounted roll-over protective structures on narrow-track tractors)

The test procedures and requirements applying to front mounted roll-over protective structures as regards narrow- track tractors for vehicles of categories T2, T3 and T4.3 referred to in Article 18(2)(a) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex IX to this Regulation.

Article 13 Requirements applying to roll-over protection structures (rear mounted roll-over protective structures on narrow-track tractors)

The test procedures and requirements applying to rear mounted roll-over protective structures as regards narrow-track tractors for vehicles of categories T2/C2, T3/C3 and T4.3/C4.3 referred to in Article 18(2)(a) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex X to this Regulation.

Article 14 Requirements applying to falling objects protection structures

The test procedures and requirements applying to falling objects protection structures for vehicles of categories T and C referred to in Article 18(2)(b) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex XI to this Regulation.

Article 15 Requirements applying to passenger seats

The test procedures and requirements applying to passenger seats for vehicles of categories T and C referred to in Article 18(2)(c) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex XII to this Regulation.

Article 16 Requirements applying to the driver’s exposure to noise level

The test procedures and requirements applying to the driver’s exposure to noise level for vehicles of categories T and C referred to in Article 18(2)(d) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex XIII to this Regulation.

Article 17 Requirements applying to the driving seat

The test procedures and requirements applying to the driving seat for vehicles of categories T and C referred to in Article 18(2)(e) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex XIV to this Regulation.

Article 18 Requirements applying to operating space and to access to the driving position

The test procedures and requirements applying to operating space and to access to the driving position for vehicles of categories T and C referred to in Article 18(2)(f) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex XV to this Regulation.

Article 19 Requirements applying to power take-offs

The test procedures and requirements applying to power take-offs for vehicles of categories T and C referred to in Article 18(2)(g) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex XVI to this Regulation.

Article 20 Requirements applying to the protection of drive components

The test procedures and requirements applying to protection of drive components for vehicles of categories T and C referred to in Article 18(2)(h) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex XVII to this Regulation.

Article 21 Requirements applying to seat-belt anchorages

The test procedures and requirements applying to seat-belt anchorages for vehicles of categories T and C referred to in Article 18(2)(i) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex XVIII to this Regulation.

Article 22 Requirements applying to safety belts

The test procedures and requirements applying to safety belts for vehicles of categories T and C referred to in Article 18(2)(j) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex XIX to this Regulation.

Article 23 Requirements applying to the protection against penetrating objects

The test procedures and requirements applying to the protection against penetrating objects for vehicles of categories T and C referred to in Article 18(2)(k) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex XX to this Regulation.

Article 24 Requirements applying to exhaust systems

The test procedures and requirements applying to exhaust systems for vehicles of categories T and C referred to in Article 18(2)(l) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex XXI to this Regulation.

Article 25 Requirements applying to the operator’s manual

The requirements applying to the operator’s manual, including aspects relating to the protection against hazardous substances and operation and maintenance of the vehicle, for vehicles of categories T, C, R and S referred to in points (l), (n) and (q) of Article 18(2) of Regulation (EU) No 167/2013 shall be laid down in Annex XXII to this Regulation.

Article 26 Requirements applying to control devices, including safety and reliability of control systems and emergency and automatic stop devices

The test procedures and requirements applying to control devices, including safety and reliability of control systems and emergency and automatic stop devices for vehicles of categories T and C referred to in Article 18(2)(o) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex XXIII to this Regulation.

Article 27 Requirements applying to the protection against other mechanical hazards

The test procedures and requirements applying to the protection against mechanical hazards, including aspects relating to the protection against rough surfaces, sharp edges and angles, rupture of pipes carrying fluids and uncontrolled movement of the vehicle, other than those mentioned in Articles 9 to 14, 19 and 23 for vehicles of categories T, C, R and S referred to in Article 18(2)(p) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex XXIV to this Regulation.

Article 28 Requirements applying to guards and protective devices

The test procedures and requirements applying to guards and protective devices for vehicles of categories T, C, R and S referred to in Article 18(2)(r) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex XXV to this Regulation.

Article 29 Requirements applying to information, warnings and markings

The test procedures and requirements applying to information, warnings and markings, including aspects relating to the warning signals with regard to braking and the operation and maintenance of the vehicle, for vehicles of categories T, C, R and S referred to in Article 18(2)(s) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex XXVI to this Regulation.

Article 30 Requirements applying to materials and products

The test procedures and requirements applying to materials and products for vehicles of categories T and C referred to in Article 18(2)(t) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex XXVII to this Regulation.

Article 31 Requirements applying to batteries

The test procedures and requirements applying to batteries for vehicles of categories T and C referred to in Article 18(2)(u) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex XXVIII to this Regulation.

Article 32 Requirements applying to protection against hazardous substances

The test procedures and requirements applying to protection against hazardous substances for vehicles of categories T and C referred to in Article 18(2)(l) of Regulation (EU) No 167/2013 shall be conducted and verified in accordance with Annex XXIX to this Regulation.