http://www.legislation.gov.uk/id/eur/2012/205

Commission Delegated Regulation (EU) No 205/2012

of 6 January 2012

amending Annex II to Regulation (EU) No 510/2011 of the European Parliament and of the Council with regard to the data source and the data parameters to be reported by Member States

(Text with EEA relevance)

THE EUROPEAN COMMISSION,

Having regard to the Treaty on the Functioning of the European Union,

Having regard to Regulation (EU) No 510/2011 of the European Parliament and of the Council of 11 May 2011 setting emission performance standards for new light commercial vehicles as part of the Union’s integrated approach to reduce CO₂ emissions from light-duty vehicles1, and in particular the second subparagraph of Article 8(9) thereof,

Whereas:

(1)

Pursuant to Articles 18 and 26 of Directive 2007/46/EC of the European Parliament and of the Council of 5 September 2007 establishing a framework for the approval of motor vehicles and their trailers, and of systems, components and separate technical units intended for such vehicles2, a manufacturer must ensure that each new light commercial vehicle placed on the market in the Union is accompanied by a valid certificate of conformity and a Member State may not register such a vehicle unless it is accompanied by such a certificate. In accordance with Annex II to Regulation (EU) No 510/2011, data collected by a Member State to monitor the manufacturer’s compliance with Articles 4 and 11 of that Regulation are to be consistent with a certificate of conformity and based on this document only.

(2)

Regulation (EC) No 443/2009 of the European Parliament and of the Council of 23 April 2009 setting emission performance standards for new passenger cars as part of the Community’s integrated approach to reduce CO₂ emissions from light-duty vehicles3 requires the Member States to use the certificate of conformity as a data source but allows for the use of other documents providing equivalent accuracy for the monitoring and reporting of CO₂ emissions from passenger cars. In order to ensure cost-efficient and accurate monitoring and reporting of CO₂ emissions data for light commercial vehicles, it is appropriate in the short-term to allow Member States to use the same procedure and data sources for the monitoring and reporting under Regulation (EU) No 510/2011 as those used for reporting under Regulation (EC) No 443/2009. Therefore, Annex II to Regulation (EU) No 510/2011 should, where duly justified, allow for the use of other data sources providing equivalent accuracy for CO₂ monitoring and reporting purposes. The Member States should put the necessary measures in place to ensure adequate accuracy in the monitoring procedure.

(3)

Based on the experience gained from the monitoring of CO₂ emissions from passenger cars, it is appropriate, in order to improve the means for verifying the accuracy of the data, to add type-approval number as a detailed data parameter to be reported by Member States. It has also become evident that there is no need for the parameter ‘commercial name’ which therefore should be deleted from the detailed monitoring data.

(4)

In order to ensure clarity and precision in the monitoring and reporting by Member States, it is also necessary to ensure consistency between the different requirements specified in Annex II to Regulation (EU) No 510/2011. The detailed data requirements are specified in the reporting formats set out in Part C of Annex II. Parts A and B of that Annex should therefore be adjusted to reflect those detailed data requirements accurately.

(5)

Annex II to Regulation (EU) No 510/2011 should therefore be amended accordingly,

HAS ADOPTED THIS REGULATION:

Article 1

Annex II to Regulation (EU) No 510/2011 is amended in accordance with the Annex to this Regulation.

Article 2

This Regulation shall enter into force on the third day following its publication in the Official Journal of the European Union.

This Regulation shall be binding in its entirety and directly applicable in all Member States.

Done at Brussels, 6 January 2012.

For the Commission

The President

José Manuel Barroso

ANNEX

Annex II to Regulation (EU) No 510/2011 is amended as follows:

(1)
Part A is amended as follows:
1. (a)
  in point 2, the first sentence is replaced by the following:
  ‘The details referred to in point 1 shall be taken from the certificate of conformity or be consistent with the certificate of conformity issued by the manufacturer of the relevant light commercial vehicle. Where the certificate of conformity is not used, Member States shall put the necessary measures in place to ensure adequate accuracy in the monitoring procedure.’;
2. (b)
  point 3 is amended as follows:
  1. (i)
    point (b) is replaced by the following:
    ‘(b)
    The number of new light commercial vehicles having values for each of the following parameters:
    (i)
    CO₂ emissions;
    (ii)
    mass;
    (iii)
    wheelbase;
    (iv)
    track width steering axle;
    (v)
    track width other axle.’;
  2. (ii)
    point (c) is deleted;
  3. (iii)
    in point (d), points (iv) and (v) are replaced by the following:
    ‘(iv)
    technically permissible maximum laden mass;
    (v)
    wheelbase;
    (vi)
    track width steering axle;
    (vii)
    track width other axle.’;
(2)
in Part B, points 2, 3, 5 and 6 are deleted;

(3)

in Part C, Section 2 on detailed monitoring data is replaced by the following:

‘Section 2 —Detailed monitoring data
Manufacturer name — EU standard denomination
Manufacturer name — Manufacturer denomination
Manufacturer name — National Registry denomination
Type-approval number and its extension(s)
Type
Variant
Version
Make
Category of vehicle type-approved
Category of vehicle registered
Total number of new registrations
Specific emissions of CO₂ (g/km)
Mass (kg)
Technically permissible maximum laden mass (kg)
Wheelbase (mm)
Track width steering axle (mm)
Track width other axle (mm)
Fuel type
Fuel mode
Capacity (cm³)
Electric energy consumption (Wh/km)
Innovative technology or group of innovative technologies code
Emissions reduction through innovative technologies
Manuf. 1
Manuf. 1
Manuf. 1
Number 1
Type 1
Variant 1
Version 1
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
Manuf. 1
Manuf. 1
Manuf. 1
Number 1
Type 1
Variant 1
Version 2
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
Manuf. 1
Manuf. 1
Manuf. 1
Number 1
Type 1
Variant 2
Version 1
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
Manuf. 1
Manuf. 1
Manuf. 1
Number 1
Type 1
Variant 2
Version 2
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
Manuf. 1
Manuf. 1
Manuf. 1
Number 2
Type 2
Variant 1
Version 1
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
Manuf. 1
Manuf. 1
Manuf. 1
Number 2
Type 2
Variant 1
Version 2
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
Manuf. 1
Manuf. 1
Manuf. 1
Number 2
Type 2
Variant 2
Version 1
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
Manuf. 1
Manuf. 1
Manuf. 1
Number 2
Type 2
Variant 2
Version 2
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
Manuf. 2
Manuf. 2
Manuf. 2
Number 1
Type 1
Variant 1
Version 1
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
Manuf. 2
Manuf. 2
Manuf. 2
Number 1
Type 1
Variant 1
Version 2
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
Manuf. 2
Manuf. 2
Manuf. 2
Number 1
Type 1
Variant 2
Version 1
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
Manuf. 2
Manuf. 2
Manuf. 2
Number 1
Type 1
Variant 2
Version 2
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…
…’

Manufacturer name — EU standard denomination	Manufacturer name — Manufacturer denomination	Manufacturer name — National Registry denomination	Type-approval number and its extension(s)	Type	Variant	Version	Make	Category of vehicle type-approved	Category of vehicle registered	Total number of new registrations	Specific emissions of CO₂ (g/km)	Mass (kg)	Technically permissible maximum laden mass (kg)	Wheelbase (mm)	Track width steering axle (mm)	Track width other axle (mm)	Fuel type	Fuel mode	Capacity (cm³)	Electric energy consumption (Wh/km)	Innovative technology or group of innovative technologies code	Emissions reduction through innovative technologies
Manuf. 1	Manuf. 1	Manuf. 1	Number 1	Type 1	Variant 1	Version 1	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…
Manuf. 1	Manuf. 1	Manuf. 1	Number 1	Type 1	Variant 1	Version 2	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…
Manuf. 1	Manuf. 1	Manuf. 1	Number 1	Type 1	Variant 2	Version 1	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…
Manuf. 1	Manuf. 1	Manuf. 1	Number 1	Type 1	Variant 2	Version 2	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…
Manuf. 1	Manuf. 1	Manuf. 1	Number 2	Type 2	Variant 1	Version 1	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…
Manuf. 1	Manuf. 1	Manuf. 1	Number 2	Type 2	Variant 1	Version 2	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…
Manuf. 1	Manuf. 1	Manuf. 1	Number 2	Type 2	Variant 2	Version 1	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…
Manuf. 1	Manuf. 1	Manuf. 1	Number 2	Type 2	Variant 2	Version 2	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…
Manuf. 2	Manuf. 2	Manuf. 2	Number 1	Type 1	Variant 1	Version 1	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…
Manuf. 2	Manuf. 2	Manuf. 2	Number 1	Type 1	Variant 1	Version 2	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…
Manuf. 2	Manuf. 2	Manuf. 2	Number 1	Type 1	Variant 2	Version 1	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…
Manuf. 2	Manuf. 2	Manuf. 2	Number 1	Type 1	Variant 2	Version 2	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…	…’