1.In determining the product-type, a manufacturer may replace type-testing or type-calculation by Appropriate Technical Documentation demonstrating that:
(a)for one or several essential characteristics of the construction product, which the manufacturer places on the market, that product is deemed to achieve a certain level or class of performance without testing or calculation, or without further testing or calculation, in accordance with the conditions set out in the relevant harmonised technical specification or [F1established by the Secretary of State under Article 27(5)];
(b)the construction product, covered by a [F2designated] standard, which the manufacturer places on the market corresponds to the product-type of another construction product, manufactured by another manufacturer and already tested in accordance with the relevant [F2designated] standard. When these conditions are fulfilled, the manufacturer is entitled to declare performance corresponding to all or part of the test results of this other product. The manufacturer may use the test results obtained by another manufacturer only after having obtained an authorisation of that manufacturer, who remains responsible for the accuracy, reliability and stability of those test results; or
(c)the construction product, covered by a harmonised technical specification, which the manufacturer places on the market is a system made of components, which the manufacturer assembles duly following precise instructions given by the provider of such a system or of a component thereof, who has already tested that system or that component for one or several of its essential characteristics in accordance with the relevant harmonised technical specification. When these conditions are fulfilled, the manufacturer is entitled to declare performance corresponding to all or part of the test results for the system or the component provided to him. The manufacturer may use the test results obtained by another manufacturer or system provider only after having obtained an authorisation of that manufacturer or system provider, who remains responsible for the accuracy, reliability and stability of those test results.
2.If the construction product referred to in paragraph 1 belongs to a family of construction products for which the applicable system for assessment and verification of constancy of performance is system 1 + or 1, as set out in Annex V, the Appropriate Technical Documentation referred to in paragraph 1 shall be verified by [F3an approved] product certification body as referred to in Annex V.
Textual Amendments
F1Words in Art. 36(1)(a) substituted (31.12.2020) by The Construction Products (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/465), reg. 1, Sch. 1 para. 35(2)(a) (with Sch. 1 para. 70) (as amended by S.I. 2020/1359, reg. 1, Sch. 1 para. 17); 2020 c. 1, Sch. 5 para. 1(1)
F2Word in Art. 36(1)(b) substituted (31.12.2020) by The Construction Products (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/465), reg. 1, Sch. 1 para. 35(2)(b) (with Sch. 1 para. 70) (as amended by S.I. 2020/1359, reg. 1, Sch. 1 para. 17); 2020 c. 1, Sch. 5 para. 1(1)
F3Words in Art. 36(2) substituted (31.12.2020) by The Construction Products (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/465), reg. 1, Sch. 1 para. 35(3) (with Sch. 1 para. 70) (as amended by S.I. 2020/1359, reg. 1, Sch. 1 para. 17); 2020 c. 1, Sch. 5 para. 1(1)
Micro-enterprises manufacturing construction products covered by a [F4designated] standard may replace the determination of the product-type on the basis of type-testing for the applicable systems 3 and 4 as set out in Annex V by using methods differing from those contained in the applicable [F4designated] standard. Those manufacturers may also treat construction products to which system 3 applies in accordance with provisions for system 4. When a manufacturer uses these simplified procedures, the manufacturer shall demonstrate compliance of the construction product with the applicable requirements by means of a Specific Technical Documentation and shall demonstrate the equivalence of the procedures used to the procedures laid down in the [F4designated] standards.
Textual Amendments
F4Word in Art. 37 substituted (31.12.2020) by The Construction Products (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/465), reg. 1, Sch. 1 para. 36 (with Sch. 1 para. 70) (as amended by S.I. 2020/1359, reg. 1, Sch. 1 para. 17); 2020 c. 1, Sch. 5 para. 1(1)
1.In relation to construction products covered by a [F5designated] standard and which are individually manufactured or custom-made in a non-series process in response to a specific order, and which are installed in a single identified construction work, the performance assessment part of the applicable system, as set out in Annex V, may be replaced by the manufacturer by Specific Technical Documentation demonstrating compliance of that product with the applicable requirements and equivalence of the procedures used to the procedures laid down in the [F5designated] standards.
2.If the construction product referred to in paragraph 1 belongs to a family of construction products for which the applicable system for assessment and verification of constancy of performance is system 1 + or 1, as set out in Annex V, the Specific Technical Documentation shall be verified by [F6an approved] product certification body as referred to in Annex V.
Textual Amendments
F5Word in Art. 38(1) substituted (31.12.2020) by The Construction Products (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/465), reg. 1, Sch. 1 para. 37(2) (with Sch. 1 para. 70) (as amended by S.I. 2020/1359, reg. 1, Sch. 1 para. 17); 2020 c. 1, Sch. 5 para. 1(1)
F6Words in Art. 38(2) substituted (31.12.2020) by The Construction Products (Amendment etc.) (EU Exit) Regulations 2019 (S.I. 2019/465), reg. 1, Sch. 1 para. 37(3) (with Sch. 1 para. 70) (as amended by S.I. 2020/1359, reg. 1, Sch. 1 para. 17); 2020 c. 1, Sch. 5 para. 1(1)