Please note that the date you requested in the address for this web page is not an actual date upon which a change occurred to this item of legislation. You are being shown the legislation from , which is the first date before then upon which a change was made.
ANNEX IU.K.
“Appendix 1Information document No … pursuant to Annex I of Council Directive 70/156/EEC() relating to EC type-approval of a vehicle with respect to the permissible sound level and the exhaust system (Directive 70/157/EEC, as last amended by Directive …/…/EC)
The following information, if applicable, must be supplied in triplicate and include a list of contents. Any drawings must be supplied in appropriate scale and in sufficient detail on size A4 or on a folder of A4 format. Photographs, if any, must show sufficient detail.
If the systems, components or separate technical units have electronic controls, information concerning their performance must be supplied.
0.GeneralU.K.
0.1.Make (trade name of manufacturer):U.K.
0.2.Type and general commercial description(s):U.K.
0.3.Means of identification of type, if marked on the vehicle (b):U.K.
0.3.1.Location of that marking.U.K.
0.4.Category of vehicle (c):U.K.
0.5.Name and address of manufacturer:U.K.
0.8.Address(es) of assembly plant(s):U.K.
1.General construction characteristics of the vehicleU.K.
1.1.Photographs and/or drawings of a representative vehicle:U.K.
1.3.3.Powered axles (number, position, interconnection):U.K.
1.6.Position and arrangement of the engine:U.K.
2.Masses and dimensions (e) (in kg and mm) (Refer to drawing where applicable)U.K.
2.4.Range of vehicle dimensions (overall)U.K.
2.4.1.For chassis without bodyworkU.K.
2.4.1.1.Length (j):U.K.
2.4.1.2.Width (k):U.K.
2.4.2.For chassis with bodyworkU.K.
2.4.2.1.Length (j):U.K.
2.4.2.2.Width (k):U.K.
2.6.Mass of the vehicle with bodywork in running order, or mass of the chassis with cab if the manufacturer does not fit the bodywork (with standard equipment, including coolant, oils, fuel, tools, spare wheel and driver) (o) (maximum and minimum):U.K.
3.Power plant (q)U.K.
3.1.Manufacturer:U.K.
3.1.1.Manufacturer's engine code: (As marked on the engine, or other means of identification)U.K.
3.2.Internal combustion engineU.K.
3.2.1.1.Working principle: positive ignition/compression ignition, four stroke/two stroke() U.K.
3.2.1.2.Number and arrangement of cylinders:U.K.
3.2.1.2.3.Firing order:U.K.
3.2.1.3.Engine capacity (s): cm3 U.K.
3.2.1.8.Maximum net power (t): kW at min–1 (manufacturer's declared value)U.K.
3.2.4.Fuel feedU.K.
3.2.4.1.By carburettor(s): yes/no() U.K.
3.2.4.1.2.Type(s):U.K.
3.2.4.1.3.Number fitted:U.K.
3.2.4.2.By fuel injection (compression ignition only): yes/no() U.K.
3.2.4.2.2.Working principle: Direct injection/pre-chamber/swirl chamber() U.K.
3.2.4.2.4.GovernorU.K.
3.2.4.2.4.1.Type:U.K.
3.2.4.2.4.2.1.Cut-off point under load: min–1 U.K.
3.2.4.3.By fuel injection (positive ignition only): yes/no() U.K.
3.2.4.3.1.Working principle: Intake manifold (single-/multi-point())/direct injection/other (specify)() U.K.
3.2.8.Intake systemU.K.
3.2.8.4.2.Air filter, drawings; orU.K.
3.2.8.4.2.1.Make(s):U.K.
3.2.8.4.2.2.Type(s):U.K.
3.2.8.4.3.Intake silencer, drawings; orU.K.
3.2.8.4.3.1.Make(s):U.K.
3.2.8.4.3.2.Type(s):U.K.
3.2.9.Exhaust systemU.K.
3.2.9.2.Description and/or drawing of the exhaust system:U.K.
3.2.9.4.Exhaust silencer(s):U.K.
For front, centre, rear silencer: construction, type, marking, where relevant for exterior noise: reducing measures in the engine compartment and on the engine:U.K.
3.2.9.5.Location of the exhaust outlet:U.K.
3.2.9.6.Exhaust silencer containing fibrous materials:U.K.
3.2.12.2.1.Catalytic convertor: yes/no() U.K.
3.2.12.2.1.1.Number of catalytic convertors and elements:U.K.
3.3.Electric motorU.K.
3.3.1.Type (winding, excitation):U.K.
3.3.1.1.Maximum hourly output: kWU.K.
3.3.1.2.Operating voltage: VU.K.
3.4.Other engines or motors or combinations thereof (particulars regarding the parts of such engines or motors):U.K.
4.Transmission (v)U.K.
4.2.Type (mechanical, hydraulic, electric, etc.):U.K.
4.6.Gear ratiosU.K.
| |
| Gear | Internal gearbox ratios(ratios of engine to gearbox output shaft revolutions) | Final drive ratio(s)(ratio of gearbox output shaft to driven wheel revolutions) | Total gear ratios |
|---|
| Maximum for CVT
1
2
3
…
Minimum for CVT
Reverse
| | | |
4.7.Maximum vehicle speed (and gear in which this is achieved) (in km/h) (w):U.K.
6.SuspensionU.K.
6.6.Tyres and wheelsU.K.
6.6.2.Upper and lower limits of rolling radiiU.K.
6.6.2.1.Axle 1:U.K.
6.6.2.2.Axle 2:U.K.
6.6.2.3.Axle 3:U.K.
6.6.2.4.Axle 4:U.K.
etc.
9.Bodywork (not applicable for vehicles of category M1)U.K.
9.1.Type of bodywork:U.K.
9.2.Materials used and method of constructionU.K.
12.MiscellaneousU.K.
12.5.Details of any non-engine devices designed to reduce noise (if not covered by other items):U.K.
Additional information in the case of off-road vehicles:U.K.
1.3.Number of axles and wheels:U.K.
2.4.1.For chassis without bodyworkU.K.
2.4.1.4.1.Approach angle (na): … degreesU.K.
2.4.1.5.1.Departure angle (nb): … degreesU.K.
2.4.1.6.Ground clearance (as defined in point 4.5 of section A of Annex II to Directive 70/156/EEC)U.K.
2.4.1.6.1.Between the axles:U.K.
2.4.1.6.2.Under the front axle(s):U.K.
2.4.1.6.3.Under the rear axle(s):U.K.
2.4.1.7.Ramp angle (nc): … degreesU.K.
2.4.2.For chassis with bodyworkU.K.
2.4.2.4.1.Approach angle (na): … degreesU.K.
2.4.2.5.1.Departure angle (nb): … degreesU.K.
2.4.2.6.Ground clearance (as defined in point 4.5 of section A of Annex II to Directive 70/156/EEC)U.K.
2.4.2.6.1.Between the axles:U.K.
2.4.2.6.2.Under the front axle(s):U.K.
2.4.2.6.3.Under the rear axle(s):U.K.
2.4.2.7.Ramp angle (nc): … degreesU.K.
2.15.Hill-starting ability (solo vehicle): … percentU.K.
4.9.Differential lock: yes/no/optional() U.K.
Date, File”