xmlns:atom="http://www.w3.org/2005/Atom" xmlns:atom="http://www.w3.org/2005/Atom"

PART 2U.K.REGULATED NON-AUTOMATIC WEIGHING INSTRUMENTS – OBLIGATIONS OF ECONOMIC OPERATORS

CHAPTER 4U.K.IDENTIFICATION OF ECONOMIC OPERATORS

32.—(1) Economic operators must, on request, identify to the market surveillance authorities—

(a)any economic operator who has supplied them with a regulated non-automatic weighing instrument; and

(b)any economic operator to whom they have supplied a regulated non-automatic weighing instrument.

(2) Economic operators must be able to present the information referred to in paragraph (1) for 10 years beginning with the day on which they have been supplied with the regulated non-automatic weighing instrument and for 10 years beginning with the day after the day on which they have supplied the instrument.

(3) The Secretary of State may impose a monetary penalty on an economic operator who fails to comply with an obligation imposed by this regulation.

(4) Schedule 5 has effect in relation to the imposition of a monetary penalty under paragraph (3).

[F1Obligations which are met by complying with obligations in the DirectiveE+W+S

32A.—(1) In this regulation—

(a)any reference to an Article or an Annex is a reference to an Article or an Annex of the Directive;

(b)“CE marking” has the meaning given to it in Article 2(19);

(c)“Module B” means the conformity assessment procedure set out in point 1 of Annex II;

(d)“EU-type examination certificate” means an EU-type examination certificate issued in accordance with Module B;

(e)“harmonised standard” has the meaning given to it in Article 2(11).

(2) Paragraph (3) applies where, before placing a non-automatic weighing instrument on the market, the manufacturer—

(a)ensures that the non-automatic weighing instrument has been designed and manufactured in accordance with the essential requirements set out in Annex I;

(b)ensures that the relevant conformity assessment procedures that apply to that non-automatic weighing instrument in accordance with Article 13 have been carried out;

(c)draws up the technical documentation referred to in Annex II;

(d)ensures that the technical documentation and other records and correspondence relating to the conformity assessment procedures are prepared in or translated into English;

(e)affixes the CE marking and the supplementary metrology marking, in accordance with Articles 16 and 17(1) to (5);

(f)affixes the inscriptions provided for in points 1 or 2 of Annex III in accordance with Article 6(5);

(g)affixes where required in accordance with Article 6(5) the restrictive use symbol as provided for in Article 18 and in point 3 of Annex III;

(h)draws up an EU declaration of conformity, in accordance with Article 14; and

(i)ensures that the EU declaration of conformity is prepared in or translated into English.

(3) Where this paragraph applies—

(a)the requirements of regulations 6, 9(3) and (4), 41 and 45(2) are to be treated as being satisfied;

(b)regulations 7, 8(2), 44, 63(1)(a) to (e), 67, 68 and 71 apply subject to the modifications in paragraph (8); and

(c)Regulations 34 to 36 do not apply.

(4) Paragraph (5) applies where, before placing a regulated non-automatic weighing instrument on the market, the importer ensures that—

(a)the relevant conformity assessment procedure referred to in Article 13 has been carried out;

(b)the manufacturer has drawn up the technical documentation referred to in Annex II; and

(c)the non-automatic weighing instrument bears the CE marking and supplementary metrology marking in accordance with Articles 16 and 17(1) to (5).

(5) Where this paragraph applies—

(a)the requirements of regulation 16(2)(a) to (c) are to be treated as being satisfied; and

(b)regulations 23, 63(1)(a) to (e), 67 and 68 apply subject to the modifications in paragraph (8).

(6) Paragraph (7) applies where, before making a regulated non-automatic weighing instrument available on the market, a distributor ensures that the non-automatic weighing instrument bears the CE marking and the inscriptions referred to in point 1 of Annex III.

(7) Where this paragraph applies—

(a)regulation 27(1) is to be treated as being satisfied; and

(b)regulations 28(1), 28(2), 29, 63(1)(a), 63(1)(b), 67, 68 and 71 apply subject to the modifications in paragraph (8).

(8) The modifications referred to in sub-paragraphs (3)(b), (5)(b) and (7)(b) are that—

(a)any reference to “declaration of conformity” is to be read as a reference to the EU declaration of conformity;

(b)any reference to “UK marking” is to be read as a reference to the CE marking;

(c)any reference to “designated standard” is to be read as a reference to a harmonised standard;

(d)any reference to “relevant conformity assessment procedure” is to be read as a reference to the relevant conformity assessment procedures referred to in Article 13;

(e)any reference to “technical documentation” is to be read as a reference to the technical documentation referred to in Annex II;

(f)any reference to “type examination certificate” is to be read as a reference to an EU-type examination certificate;

(g)any reference to “M marking” is to be read as a reference to the supplementary metrology marking;

(h)[F2except in relation to regulation 68,] any reference to “approved body” is to be read as a reference to the body that undertook any conformity assessment procedure in accordance with Article 13;

(i)any reference to “authorised mark” includes the CE marking and the supplementary metrology marking.]

Textual Amendments

[F1Conformity assessment procedure obligations that are met by complying with the DirectiveE+W+S

32B.—(1) In this regulation—

(a)any reference to an Article or an Annex is a reference to an Article or an Annex of the Directive;

(b)“EU-type examination certificate” means an EU-type examination certificate issued in accordance with the conformity assessment procedure set out in point 1 of Annex II (Module B);

(c)any reference to “the first stage of the conformity assessment procedure” is a reference to one or both of the following—

(i)all examinations and tests which are not gravity dependent and which are included in the conformity assessment procedures set out in points 2 to 5 of Annex II;

(ii)the examinations and tests included in the conformity assessment procedures set out in points 2 to 5 of Annex II that may be carried out at the manufacturer's works or any other location where—

(aa)the transport of the instrument to its place of use requires dismantling of the instrument; or

(bb)the putting into service of the instrument in its place of use requires assembly of the instrument or other technical installation work that is likely to affect the instrument's performance.

(2) Paragraph (3) applies where, prior to the manufacture of a non-automatic weighing instrument the manufacturer has ensured that the conformity assessment procedure as set out in point 1 of Annex II (Module B) has been carried out.

(3) Where this paragraph applies—

(a)the reference in regulation 36(a) to “Module B as set out in point 1 of Schedule 7” is to be read as a reference to the conformity assessment procedure as set out in point 1 of Annex II (Module B); and

(b)regulations 6(b) and (c), 7, 16(2)(a) and (b), 63(1)(e), 67(2)(b), 68(4)(b) and paragraph 1 of Schedule 1 apply subject to the modifications in paragraph (6).

(4) Paragraph (5) applies where—

(a)in accordance with point 7.1 of Annex II, the procedures set out in points 2 to 5 of that Annex may be carried out in two stages; and

(b)the first stage of the conformity assessment procedure is carried out in accordance with any of the following points of Annex II—

(i)point 2 (Module D);

(ii)point 3 (Module D1);

(iii)point 4 (Module F); or

(iv)point 5 (Module F1).

(5) Where this paragraph applies—

(a)the reference in regulation 36(1)(a)(i) to “Module D as set out in point of Schedule 7” is to be read as including the first stage of the conformity assessment procedure as set out in point 2 of Annex II (Module D);

(b)the reference in regulation 36(1)(a)(ii) to “Module F as set out in point 4 of Schedule 7” is to be read as including the first stage of the conformity assessment procedure as set out in point 4 of Annex II (Module F);

(c)the reference in regulation 36(3)(a) to “Module D1 as set out in point 3 of Schedule 7” is to be read as including the first stage of the conformity assessment procedure as set out in point 3 of Annex II (Module D1);

(d)the reference in regulation 36(3)(b) to “Module F1 as set out in point 5 of Schedule 7” is to be read as including the first stage of the conformity assessment procedure as set out in point 5 of Annex II (Module F1);

(e)regulations 6(b) and (c), 7, 16(2)(a) and (b), 45(6) and (7), 63(1)(c) and (e) and 67(1)(c) apply subject to the modifications in paragraph (6).

(6) The modifications referred to in paragraphs (3)(b) and (5)(e) are that—

(a)any reference to “relevant conformity assessment procedure” is to be read as including—

(i)where paragraph (3) applies, the conformity assessment procedure set out in point 1 of Annex II;

(ii)where paragraph (5) applies, the relevant first stage conformity assessment procedure;

(b)any reference to “type examination” is to be read as a reference to the EU-Type examination certificate;

(c)any reference to “technical documentation” is to be read as including the technical documentation required by points 1 to 5 of Annex II (as applicable);

(d)any reference to “approved body” is to be read as including the body which undertook the first stage conformity assessment procedure.]

Textual Amendments

[F1Expiry of regulations 32A and 32BE+W+S

32C.—(1) Subject to [F3paragraphs (2) and (6)], regulation 32A ceases to have effect at the end of the period of [F4four years] beginning with IP completion day.

(2) Notwithstanding the expiry of regulation 32A—

(a)any non-automatic weighing instrument which was placed on the market pursuant to regulation 32A may continue to be made available on the market on or after the expiry of regulation 32A;

(b)any obligation to which a person was subject under regulation 32A in respect of any non-automatic weighing instrument placed on the market pursuant to regulation 32A continues to have effect after the expiry of regulation 32A, in respect of that instrument.

(3) Subject to [F5paragraphs (4) and (6)], regulation 32B ceases to have effect at the end of the period of [F6four years] beginning with IP completion day.

(4) Where a conformity assessment procedure has been completed pursuant to regulation 32B in relation to a non-automatic weighing instrument prior to the expiry of regulation 32B, regulation 32B continues to apply in respect of that instrument where—

(a)the manufacturer arranges for the EU-Type examination certificate and any annexes to be transferred to an approved body;

(b)the approved body referred to in sub-paragraph (a) accepts responsibility for the EU-Type examination certificate; and

(c)the approved body issues a Type-examination certificate relying, or relying in part, on any examinations or tests undertaken prior to the issue of the EU-Type examination certificate.

(5) In paragraph (4) “EU-Type examination certificate” has the meaning given to it in regulation 32B(1)(b).

[F7(6) regulations 67 and 68 continue to have effect in relation to any non-automatic weighing instrument—

(a)placed on the market pursuant to 32A; or

(b)in relation to which a manufacturer has undertaken a conformity assessment procedure in accordance with regulation 32B,

as if regulations 32A or 32B had not expired.]

Textual Amendments

Qualifying Northern Ireland GoodsU.K.

32D.—(1) Where paragraph (2) applies—

(a)a non-automatic weighing instrument is to be treated as being in conformity with the essential requirements; and

(b)each relevant economic operator is to be treated as having complied or as complying with the obligations imposed on them under Part 2.

(2) This paragraph applies where—

(a)a non-automatic weighing instrument is—

(i)in conformity with the essential requirements, within the meaning of that term in regulation 2, as it applies in Northern Ireland; and

(ii)qualifying Northern Ireland goods;

(b)each relevant economic operator has complied or is complying with the obligations imposed on them under Part 2, as that Part applies in Northern Ireland; and

(c)an importer has complied with the obligations set out in paragraph (3).

(3) The obligations referred to in paragraph (2)(c) are that, before placing the non-automatic weighing instrument on the market, the importer—

(a)complies with regulation 18;

(b)ensures that—

(i)the relevant conformity assessment procedure has been carried out in accordance with Part 3, as that Part applies in Northern Ireland;

(ii)the manufacturer has drawn up the technical documentation; and

(iii)the non-automatic weighing instrument bears the CE marking.

[F8(3A) After a non-automatic weighing instrument has been placed on the market pursuant to this regulation, regulations 67 and 68 are to be read in relation to that instrument subject to the following modifications—

(a)the reference in regulation 67(1)(a) to “UK marking” is to be read as a reference to the CE marking, within the meaning of regulation 2(1) as it applies in Northern Ireland;

(b)the reference in regulation 67(1)(b) to “M marking”, is to be read as a reference to the M Marking as defined in regulation 2(1), as it applies in Northern Ireland;

(c)the reference in regulation 67(1)(c) to “approved body” is to be read as a reference to a “notified body” as defined in regulation 2(1), as it applies in Northern Ireland;

(d)the references in regulations 67(2)(a) and 68(4)(a) to “essential requirements” are to be read as the essential requirements within the meaning of that term in regulation 2(1), as it applies in Northern Ireland; and

(e)the references in regulations 67(2)(b) and 68(4)(b) to “type examination certificate” is to be read as a reference to an EU-type examination certificate as defined in regulation 2(1), as it applies in Northern Ireland.]

(4) In this regulation—

“CE marking” has the meaning given to it in regulation 2(1), as it applies in Northern Ireland;

“qualifying Northern Ireland goods” has the meaning given to it in regulations made under section 8C(6) of the European Union (Withdrawal) Act 2018;

“technical documentation” has the meaning given to it in regulation 2(1), as it applies in Northern Ireland.]

Textual Amendments