The Disabled Persons (Badges for Motor Vehicles) (EU Exit) (Scotland) (Amendment) Regulations 2019

Citation and commencement

1.—(1) These Regulations may be cited as the Disabled Persons (Badges for Motor Vehicles) (EU Exit) (Scotland) (Amendment) Regulations 2019.

(2) These Regulations, apart from regulations 2(2) and 3, come into force at 1600 hours on 1 April 2019.

(3) Regulations 2(2) and 3 come into force on exit day.

Amendment of the Disabled Persons (Badges for Motor Vehicles) (Scotland) Regulations 2000

2.—(1) The Disabled Persons (Badges for Motor Vehicles) (Scotland) Regulations 2000(1) are amended as follows.

(2) In regulation 2(1A) (interpretation) omit “other than the United Kingdom”.

(3) In regulation 11(form of badge)—

(a) for paragraph (1) substitute—

“(1) Paragraph (2) applies in respect of a badge with a date of issue before 1st January 2012, paragraph (3) applies in respect of a badge with a date of issue on or after that date but before 1st April 2019, and paragraph (4) applies in respect of a badge with a date of issue on or after 1st April 2019.”,

(b) after paragraph (3), insert—

“(4) A disabled person’s badge is in the prescribed form if—

(a) the front and reverse of the badge are in the form shown in—

(i) Part IB of the Schedule in the case of an individual’s badge (with the omission of the word “sample” where it appears), or

(ii) Part IIB of the Schedule in the case of an organisational badge (with the omission of the word “sample” where it appears), and

(b) the badge complies with the specifications in Part IIIB of the Schedule.”.

(4) In the schedule—

(a) in the heading to Part IA, after “1ST JANUARY 2012” insert “BUT BEFORE 1ST APRIL 2019”,

(b) after that Part, insert—

“PART IB INDIVIDUAL’S BADGE WITH A DATE OF ISSUE ON OR AFTER 1ST APRIL 2019

”

(c) in the heading to Part IIA, after “1ST JANUARY 2012” insert “BUT BEFORE 1ST APRIL 2019”,

(d) after that Part, insert—

“PART IIB ORGANISATIONAL BADGE (WITH A DATE OF ISSUE ON OR AFTER 1ST APRIL 2019)

”

(e) in the heading to Part IIIA, after “1ST JANUARY 2012” insert “BUT BEFORE 1ST APRIL 2019”,

(f) after that Part, insert—

“PART IIIB SPECIFICATIONS FOR BADGES (WITH A DATE OF ISSUE ON OR AFTER 1ST APRIL 2019)

All Badges

1.   The specifications applicable to all badges are as follows—

(a) the badge must be 106 millimetres in height, 148 millimetres in width (with 5mm radius rounded corners) and 720 microns in thickness, with height and width tolerances of plus or minus 1 millimetre and a thickness tolerance of plus or minus 20 microns,

(b) the badge must be printed with a unique serial number, comprising a series of numbers and letters that identify key information about the badge and the holder, including the consecutive number of each replacement badge issued to the badge holder by the issuing authority,

(c) the rear side of the badge must contain a variable bar code which identifies the expiry date of the badge,

(e) the badge must include such additional security features as will further mitigate the risk of forgery, so far as practicable, preventing the badge from being copied readily and allowing genuine badges to be distinguished from forgeries.

Individual’s Badge

2.   The additional specifications applicable to an individual’s badge are as follows—

(a) the rear side of an individual’s badge must contain a close-up digital photograph of the head and shoulders of the badge holder and the photograph must have a strong definition between face and background and must be—

(i) in colour,

(ii) 45 millimetres in height and 35 millimetres in width (passport size),

(iii) taken—

(aa) within the month prior to the date of the application,

(bb) against a light grey or cream background,

(iv) undamaged,

(v) free from ‘redeye’, shadows, reflection or glare from spectacles,

(vi) of the full head of the holder (without any other person visible or any covering, unless it is worn for religious beliefs or medical reasons)—

(aa) facing forward,

(bb) with nothing covering the face,

(cc) looking straight at the camera,

(dd) with a neutral expression and mouth closed,

(ee) with eyes open and clearly visible (without sunglasses or tinted spectacles and without hair or spectacle frames obscuring the eyes),

(vii) in sharp focus and clear,

(viii) printed professionally or in digital format,

(ix) a true likeness, without amendment,

(b) the rear side of an individual’s badge must also contain a version of the digital photograph prescribed in subparagraph (a) which can only be viewed under UV light,

(c) subparagraphs (a) and (b) do not apply to a badge issued pursuant to an application made by a disabled person if the issuing authority is satisfied that the estimated life expectancy of that person is less than six months from the date of the application,

(d) subparagraphs (a)(vi)(cc) and (a)(vi)(dd) do not apply to photographs of children aged five years and under,

(e) the variable bar code on the rear side of the badge must identify the year of birth and (in code) the gender of the holder, and

(f) the serial number printed on the badge must identify the month and year of birth and (in code) the gender of the holder.

Organisational Badge

3.   The additional specification applicable to an organisational badge is that the reverse side must contain a colour copy of the logo of the organisation where such a logo exists, which must be 45 millimetres in height and 35 millimetres in width.”.

Amendment of the Local Authorities’ Traffic Orders (Exemptions for Disabled Persons) (Scotland) Regulations 2002

3.  In regulation 2 (interpretation) of the Local Authorities’ Traffic Orders (Exemptions for Disabled Persons) (Scotland) Regulations 2002(2) in the definition of “disabled person’s badge” omit “other than the United Kingdom”.

MICHAEL MATHESON

A member of the Scottish Government

St Andrew’s House,

Edinburgh

1st April 2019